Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2022/04/00600-228-1.pdf
Are You Ready for Lead-free? The Magazine for Electronics Assembly May 2000 www.smtmag.com Designing with CBGAs • SMT 101: Adhesives/Epoxies & DispensingDesigning with CBGAs
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20111117-PBT-002O-FORCEWare-v5-5-4.pdf
, the PBFT control software. To configure the InstaCal interface card software: 1. Run InstaCal by clicking on Start > Programs > Measurement Computing > Install. The following window displays. 2. W hen windows similar to the following display, click OK
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20111117-PBT-002O-FORCEWare-v5-5-4.pdf
, the PBFT control software. To configure the InstaCal interface card software: 1. Run InstaCal by clicking on Start > Programs > Measurement Computing > Install. The following window displays. 2. W hen windows similar to the following display, click OK
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20100525-PBT-002L-FORCEWare-v5-5-1.pdf
150-200 grams is recommended. 6. Enter the value of the strain gauge reading in the Strain Gauge field of the With Load row. Then click on the CALIBRATE button in the same row. Results similar to those shown above should display. If an “Unacceptable
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20100525-PBT-002L-FORCEWare-v5-5-1.pdf
150-200 grams is recommended. 6. Enter the value of the strain gauge reading in the Strain Gauge field of the With Load row. Then click on the CALIBRATE button in the same row. Results similar to those shown above should display. If an “Unacceptable
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20110414-PBT-002M-FORCEWare-v5-5-2.pdf
gauge reading. NOTE: A maximum load of 150-200 grams is recommended. 6. Enter the value of the strain gauge reading in the Strain Gauge field of the W ith Load row. Then click on the CALIBRATE button in the same row. Results similar to those shown above
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20100122-PBT-002J-FORCEWare-v5-4.pdf
software, the PBFT control software. To configure the InstaCal interface card software: 1. Run InstaCal by clicking on Start > Programs > Measurement Computing > Install. The following window displays. 2. When windows similar to the following display, click
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20100501-PBT-002K-FORCEWare-v5-5-0.pdf
InstaCal by clicking on Start > Programs > Measurement Computing > Install. The following window displays. 2. When windows similar to the following display, click OK on the Plug and Play Board Detection window. PBFT VS SPC User Guide Page 8 GPD Global® 01/22
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20100501-PBT-002K-FORCEWare-v5-5-0.pdf
InstaCal by clicking on Start > Programs > Measurement Computing > Install. The following window displays. 2. When windows similar to the following display, click OK on the Plug and Play Board Detection window. PBFT VS SPC User Guide Page 8 GPD Global® 01/22
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20110414-PBT-002M-FORCEWare-v5-5-2.pdf
gauge reading. NOTE: A maximum load of 150-200 grams is recommended. 6. Enter the value of the strain gauge reading in the Strain Gauge field of the W ith Load row. Then click on the CALIBRATE button in the same row. Results similar to those shown above
.png)
