GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20130801-PBT-002P-FORCEWare-v5-6-2.pdf
satisfied with the displayed calibration values, verify that the PBFT Speed Selector dial and the simulated dial are synchronized. For example, notice that the simulated dial in the previous illustration is set to 200 mm/min. This should indicate that the
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20170118-PBT-002P-FORCEWare-v5-6-3.pdf
and then repeating step 4. 5. When you are satisfied with the displayed calibration values, verify that the PBFT Speed Selector dial and the simulated dial are synchronized. For example, notice that the simu- lated dial in the previous illustration is
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20130801-PBT-002P-FORCEWare-v5-6-2.pdf
satisfied with the displayed calibration values, verify that the PBFT Speed Selector dial and the simulated dial are synchronized. For example, notice that the simulated dial in the previous illustration is set to 200 mm/min. This should indicate that the
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20151102-PBT-002P-FORCEWare-v5-6-3.pdf
simulated dial are synchronized. For example, notice that the simu- lated dial in the previous illustration is set to 200 mm/min. This should indicate that the Speed Selector dial on the PBFT is set to 200 mm/min. The dials are coordinated if, as you turn the
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20170118-PBT-002P-FORCEWare-v5-6-3.pdf
and then repeating step 4. 5. When you are satisfied with the displayed calibration values, verify that the PBFT Speed Selector dial and the simulated dial are synchronized. For example, notice that the simu- lated dial in the previous illustration is
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20121110-PBT-002P-FORCEWare-v5-6-0.pdf
are not, re-calibrate the PBFT by clicking on RESET and then repeating step 4. 5. When you are satisfied with the displayed calibration values, verify that the PBFT Speed Selector dial and the simulated dial are synchronized. For example, notice that
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20130411-PBT-002P-FORCEWare-v5-6-1.pdf
satisfied with the displayed calibration values, verify that the PBFT Speed Selector dial and the simulated dial are synchronized. For example, notice that the simulated dial in the previous illustration is set to 200 mm/min. This should indicate that the
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20211209-PBT-002P-FORCEWare-v5-7-0.pdf
simulated dial are synchronized. For example, notice that the simu- lated dial in the previous illustration is set to 200 mm/min. This should indicate that the Speed Selector dial on the PBFT is set to 200 mm/min. The dials are coordinated if, as you turn the
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20160414-PBT-002P-FORCEWare-v5-6-3.pdf
simulated dial are synchronized. For example, notice that the simu- lated dial in the previous illustration is set to 200 mm/min. This should indicate that the Speed Selector dial on the PBFT is set to 200 mm/min. The dials are coordinated if, as you turn the
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF8-Doc-Package-801-1-01.pdf
die width or pin diameter of the die to be installed. (From Chart 4 or Chart 5 in 5.3.1 Select Dies, step 3.) 3. Refer to the key listed at the end of each calculation section for abbreviations used in the formulas. Example: The figure at right
