PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/library-expert-2014-12-released_topic1449_post5847.html
(over 5,000 mfr. case codes) Allegro/OrCAD PCB: When a top pad is circular, and another pad is not but contains the rotation; the rotation will now translate properly to Allegro/OrCAD PCB Free floating areas of copper are now translated properly to the ETCH/TOP layer CADSTAR
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic1449&OB=ASC.html
(over 5,000 mfr. case codes) Allegro/OrCAD PCB: When a top pad is circular, and another pad is not but contains the rotation; the rotation will now translate properly to Allegro/OrCAD PCB Free floating areas of copper are now translated properly to the ETCH/TOP layer CADSTAR
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_library-expert-2016-10-released_topic1951.xml
STEP:Added through-hole Radial Disk Resistor and VaristorFixed Side Concave 2, 4-Pin Oscillator for micro-miniature versionPADS to CAD:Fixed a rotation problem concerning free-floating pieces of paste maskFixed an issue that was causing the corner radius on rounded rectangles to only be half what they should be when importing PADS
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/library-expert-2017-19-released_topic2237_post9249.html
. A rectangle pad stack in Cadence cannot have a corner length that exceeds more than half the width. Custom Pads which are offset from the center of the Pad Stack are now removed from the pad stack and converted to free floating copper. This is the *only
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/library-expert-2017-19-released_topic2237_post9249.html
. A rectangle pad stack in Cadence cannot have a corner length that exceeds more than half the width. Custom Pads which are offset from the center of the Pad Stack are now removed from the pad stack and converted to free floating copper. This is the *only
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/library-expert-2017-19-released_topic2237.html
. A rectangle pad stack in Cadence cannot have a corner length that exceeds more than half the width. Custom Pads which are offset from the center of the Pad Stack are now removed from the pad stack and converted to free floating copper. This is the *only
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic2237&OB=ASC.html
. A rectangle pad stack in Cadence cannot have a corner length that exceeds more than half the width. Custom Pads which are offset from the center of the Pad Stack are now removed from the pad stack and converted to free floating copper. This is the *only
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic1951&OB=ASC.html
: Fixed a rotation problem concerning free-floating pieces of paste mask Fixed an issue that was causing the corner radius on rounded rectangles to only be half what they should be when importing PADS files PADS
| https://fluxconnectivity.com/wp-content/uploads/2019/07/Technical-Introduction.pdf
. Terminal blocks provide: • A more simplified and organized layout. • An available test point and the ability for labelling when compared to a free-floating connector.
Heller Industries Inc. | https://hellerindustries.com/browse/page/40/
: 805940---Splice Bar 1812SS (Sony) 805984---End Roller Assy 805775-01---EXIT RAIL ALT. - FLOATING, FLEX DOOR (1900 W/ LODA) 805697---SHAFT, CBS LIFT 805853---DC Gearmotor, 9RPM, 90 Volt 805774-02---ENTRANCE RAIL ALT
