198 gold end termination results

Rising to New Heights: Elevating the PCB X-ray Inspection machine with High-End I.C.T Solutions - I.

| https://www.smtfactory.com/pcb-x-ray-inspection-machine

Rising to New Heights: Elevating the PCB X-ray Inspection machine with High-End I.C.T Solutions - I.C.T SMT Machine English Bahasa indonesia Сербия

Interesting Customer Questions Topics of Customer Questions • Gold plating vs Gold Flash • Gull Wing Toe Fillet requirements • Class 3 rework • Tempered leads, what are they

| https://www.eptac.com/wp-content/uploads/2016/04/eptac_04_20_16.pdf

). Final solder terminations shall not be made to any PWB or solder cup that has not had the gold removed from the termination area (Requirement). 5 The new revision of 001 now states the components must be tinned prior to assembly into the product

| https://www.eptac.com/wp-content/uploads/2012/09/eptac_10_17_12.pdf

). Final solder terminations shall not be made to any PWB or solder cup that has not had the gold removed from the termination area (Requirement). 9 Why Gold Plating Pro

| https://www.eptac.com/wp-content/uploads/2016/05/eptac_06_22_16.pdf

IPC-A-610 Acceptable Requirements for Nicks and Chip-Outs - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/ask-helena-leo/ask/ipc-a-610-acceptable-requirements-for-nicks-and-chip-outs

: In IPC-A-610 section 9.4 on page 9-8 component damage there seems to be a lack of class three acceptable requirements for nicks or chip-outs in ceramic bodied components that are not in the termination area

IPC-A-610 Acceptable Requirements for Nicks and Chip-Outs - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/ask/ipc-a-610-acceptable-requirements-for-nicks-and-chip-outs/

: In IPC-A-610 section 9.4 on page 9-8 component damage there seems to be a lack of class three acceptable requirements for nicks or chip-outs in ceramic bodied components that are not in the termination area

SolderTips: Problems With Stress Cracks in Ceramic Components | EPTAC

| https://www.eptac.com/soldertips/problems-with-stress-cracks-in-ceramic-components/

. There is lots of talk these days about using hot air to reflow the caps as the thermal ramp up with the solder iron is too quick and will potentially crack the end termination from the body of the capacitor

Solder Selection for Printed Circuit Boards and Terminals - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/ask-helena-leo/ask/solder-selection-for-printed-circuit-boards-and-terminals

. My question is, would you use that ROL0 solder on the entire solder termination when...   Question: I know for tinning stranded wires you should not use Type H or M flux, so we are ordering a No-clean solder Sn63Pb37 with a flux designator ROL0

SolderTips: Problems With Stress Cracks in Ceramic Components - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/soldertips/soldertip/soldertips-problems-with-stress-cracks-in-ceramic-components

. There is lots of talk these days about using hot air to reflow the caps as the thermal ramp up with the solder iron is too quick and will potentially crack the end termination from the body of the capacitor

Products | QYSMT

Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/page/616?order=name+asc

¥  0.00 0.0 CNY Gold Dual Lane 8mm Feeder ¥  0.00 0.0 CNY Gold plated female end ¥  0.00 0.0 CNY Gold plated male end ¥  0.00 0.0 CNY Graphite camera ¥  0.00 0.0 CNY Grease ¥  0.00 0.0 CNY Grease ¥  0.00 0.0 CNY Grease ¥  0.00 0.0 CNY Grease ¥  0.00 0.0 CNY Grease ¥  0.00 0.0 CNY Grease ¥  0.00 0.0 CNY Grease ¥  0.00

Qinyi Electronics Co.,Ltd