GPD Global | https://www.gpd-global.com/pdf/doc/SimpleCoat-Series-Operation-Guide-23100600.pdf
obstacles. Note In order for the gantry to move freely, the system must be in Emergency Stop mode. 10. Verify, and tweak as needed, the machine safety check values: home location, park location, and limit values. CAUTION Failure to successfully enter the
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Dispense-System-User-Guide-22100079K.pdf
and press the Click trackball button. 5/18/18 Dispense System User Guide 3.2 GPD Global© User Interface: Keyboard & Mouse/Trackball Keyboard When used in reference to hardware, the term key is understood to refer to a control located on the keyboard and
GPD Global | https://www.gpd-global.com/co_website/pdf/dispense/Dispensing-Systems-and-Pumps-Overview.pdf
ultra small, standard, and high volume configurations. • When configured with the smallest auger (062), the pump can dispense solder paste down to 0.005” (125 µm). This newest auger reaches a new limit of dispensing not previously possible. • Standard
GPD Global | https://www.gpd-global.com/pdf/dispense/Dispensing-Systems-and-Pumps-Overview.pdf
ultra small, standard, and high volume configurations. • When configured with the smallest auger (062), the pump can dispense solder paste down to 0.005” (125 µm). This newest auger reaches a new limit of dispensing not previously possible. • Standard
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Contour-Mapping-Calibration-User-Guide-221MAPDOC-5.pdf
power) # recommended for the glass plate illumination. mapFocus = 100 # may have better focus near upper limit of 100% # For a variable zoom lens, this value should be set near the # upper high limit of 100%. If this causes a blurry dot, use # Machine
GPD Global | https://www.gpd-global.com/pdf/doc/Contour-Mapping-Calibration-User-Guide-221MAPDOC-5.pdf
power) # recommended for the glass plate illumination. mapFocus = 100 # may have better focus near upper limit of 100% # For a variable zoom lens, this value should be set near the # upper high limit of 100%. If this causes a blurry dot, use # Machine
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Loader-and-Unloader-User-Guide-24000013M.pdf
24000013, 24000014 Magazine size, minimum 150 mm L x 35 mm D x 117 mm H (5.90” L x 1.37” D x 4.60” H) Magazine size, maximum 300 mm L x 200 mm L x 180 mm H (11.81” L x 7.87” L x 7.08” H) Magazine weight limit*, maximum 8 kg (17.6 lb) *capacity of Z-clamp and
GPD Global | https://www.gpd-global.com/pdf/doc/Loader-and-Unloader-User-Guide-24000013M.pdf
24000013, 24000014 Magazine size, minimum 150 mm L x 35 mm D x 117 mm H (5.90” L x 1.37” D x 4.60” H) Magazine size, maximum 300 mm L x 200 mm L x 180 mm H (11.81” L x 7.87” L x 7.08” H) Magazine weight limit*, maximum 8 kg (17.6 lb) *capacity of Z-clamp and
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/last-will-of-bga-void.pdf
. Until very recently, the high cost and limited availability of major computational power to do these CT calculations made it necessary to limit the CT models to smaller values such that reconstruction times were manageable, or it was necessary to have
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2022/04/last-will-of-bga-void-1.pdf
. Until very recently, the high cost and limited availability of major computational power to do these CT calculations made it necessary to limit the CT models to smaller values such that reconstruction times were manageable, or it was necessary to have