| https://www.eptac.com/soldertip/soldertip-43-ipc-j-std-001-rev-e-instructor-training-materials/
: We have been conducting operator training for both J-STD-001 and IPC-A-610 to the Revision D documents. Can you tell me when the training materials will be available for Revision E and if I have to retrain everyone to the new revision? Answer
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2022/06/Optimizing-Reflowed-Solder-TIM-sTIMs-Processes-for-Emerging-Heterogeneous.pdf
solder ball attach for BGA) on TIMs voiding. Fig. 8 below shows an x-ray result after sTIM reflow, then after subsequent SAC reflow (details later). Fig. 8: Reflow#1 vs. Reflow#2 – same part In the case of Heller Industries, the task was to establish the
Heller 公司 | http://hellerindustries.com.cn/Vacuum-Void-Reduction-Reflow.pdf
APEX 2006, S31-03-01 to S31-03-10. [12] D. R. Banks, T. E. Burnette, Y. Cho, W. T. DeMarco, and A. J. Mawer, “Effect of Solder Joint Voiding on Plastic To be published in the Proceedings of SMTA International, September 17 - 21, 2016, Rosemont, IL. Ball
| https://www.eptac.com/solder-tips/
: We have been conducting operator training for both J-STD-001 and IPC-A-610 to the Revision D documents. Can you tell me when the training materials will be available for Revision E and if I have to retrain everyone to the new revision? Answer
| https://www.eptac.com/eptac-instructors-recognized-for-industry-support-of-standard/
Lambert Recent Articles IoT and the Aerospace Industry – Too Risky? Leaded vs. Lead-Free Solder: Which is Better? The 5 Essential Tools for Soldering The Importance of IPC-A-610 Certification How to Build on Your Career in Soldering Categories Blog Uncategorized Why Get IPC Certified We would like to thank
| https://www.eptac.com/faqs/ask-helena-leo/ask/post-lead-trimming-reflow-requirements
: This following information is from Rev D of IPC-A-610. The requirement was to inspect all joints after cutting and make a determination as to whether or not the connection was damaged, then if damage was found, the solder joint was to be reflowed
| https://www.eptac.com/faqs/ask-helena-leo/ask/smt-components-during-reflow-float-off-pads
: We install D-Paks on a number of boards (8.3.14 in IPC-A-610). These parts have a tendency to float during reflow. We have done quite a bit of process work to minimize the floating, but parts do still occasionally float and are... Question
. J-STD-001, IPC-A-610 and IPC-A-620 all require solder to be “visible” in the inspection hole (if present). Is there a more specific requirement to this
| https://www.eptac.com/location/eptac-atlanta-metro-training-center?hsLang=en
@eptac.com Visual Inspection IPC-A-610 Specialist IPC-A-610 Specialist (Recert) Cable Wire Harness Assemblies IPC-A-620 Specialist IPC-A-620 Specialist (Recert
| https://www.eptac.com/location/eptac-atlanta-metro-training-center
@eptac.com Visual Inspection IPC-A-610 Specialist IPC-A-610 Specialist (Recert) Cable Wire Harness Assemblies IPC-A-620 Specialist IPC-A-620 Specialist (Recert
IPC is the trade association for the printed wiring board and electronics assembly industries.
Training Provider / Events Organizer / Association / Non-Profit
3000 Lakeside Drive, 309 S
Bannockburn, IL USA
Phone: 847-615-7100
.jpg)
