GPD Global | https://www.gpd-global.com/pdf/lead-former/CF8-Transport-Wheel-Maintenance-817-1-18.pdf
. Place a 1/8" bent hex "T" wrench (provided in tool kit) in the hole located toward the end of the transport wheel shaft and pull firmly to unlock the shaft. NOTE
| https://www.eptac.com/faqs/ask-helena-leo/ask/ipc-a-620-flag-label-secifications
14.2, Item 4, Locating Tape. “Masking tape used to position and locate harnesses and cables may be either permanent or temporary in nature, permanent type marking tapes shall meet environmental requirements
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF9-User-Guide-901-1-07.pdf
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 15 Component Position Relative to Tape Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 16 Align & Load Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 17 Die Block Assembly Lubrication
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF9-User-Guide-901-1-07.pdf
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 15 Component Position Relative to Tape Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 16 Align & Load Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 17 Die Block Assembly Lubrication
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF9-Doc-Package-901-1-01.pdf
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 15 Component Position Relative to Tape Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 16 Align & Load Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 17 Die Block Assembly Lubrication
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF9-Doc-Package-901-1-01.pdf
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 15 Component Position Relative to Tape Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 16 Align & Load Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 17 Die Block Assembly Lubrication
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF8-Doc-Package-801-1-01.pdf
) and remove the component ejector blade (Item 1) from between the transport wheel pair (Item 4). b) Place a 1/8-inch bent hex "T" wrench (provided in the tool kit) in the hole located toward the end of the transport wheel shaft (Item 5) and pull firmly
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF8-Doc-Package-801-1-01.pdf
) and remove the component ejector blade (Item 1) from between the transport wheel pair (Item 4). b) Place a 1/8-inch bent hex "T" wrench (provided in the tool kit) in the hole located toward the end of the transport wheel shaft (Item 5) and pull firmly
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF8-User-Guide-801-1-07.pdf
) and remove the component ejector blade (Item 1) from between the transport wheel pair (Item 4). b) Place a 1/8-inch bent hex "T" wrench (provided in the tool kit) in the hole located toward the end of the transport wheel shaft (Item 5) and pull firmly
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF8-User-Guide-801-1-07.pdf
) and remove the component ejector blade (Item 1) from between the transport wheel pair (Item 4). b) Place a 1/8-inch bent hex "T" wrench (provided in the tool kit) in the hole located toward the end of the transport wheel shaft (Item 5) and pull firmly