GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20130801-PBT-002P-FORCEWare-v5-6-2.pdf
Length of Test scale (see below). c. Press CARRIAGE RELEASE/LOCK to lock the carriage in place. d. Select a speed on the speed selector (Figure 1, Item 3). e. Press TEST START (Figure 2, Item 1). The following should occur: • The tape carriage will
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20151102-PBT-002P-FORCEWare-v5-6-3.pdf
. Press CARRIAGE RELEASE/LOCK (Figure 2, Item 3) to release the tape carriage. b. Manually position the tape carriage pointer (Figure 1, Item 6) with the zero (0) mark on the Length of Test scale (see below). Align tape carriage c. Press CARRIAGE RELEASE
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Process-View-Recorder-User-Guide-22200627.pdf
- delete all the files in the currently selected folder • Current - delete the currently highlighted file • Cancel - cancel delete process IMPORTANT: Manual recording length is fixed at 30 minutes per file. After 30 minutes, a new file and recording session
GPD Global | https://www.gpd-global.com/pdf/doc/Process-View-Recorder-User-Guide-22200627.pdf
- delete all the files in the currently selected folder • Current - delete the currently highlighted file • Cancel - cancel delete process IMPORTANT: Manual recording length is fixed at 30 minutes per file. After 30 minutes, a new file and recording session
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Contour-Mapping-Calibration-User-Guide-221MAPDOC-5.pdf
lowered to accommodate the glass plate in STEP 4- Prepare Work Area (page 5). 4. Reboot the system. The message Modified Servo call for Glass Plate Mapping will no longer appear in the startup sequence. 5. Teach the Base Locations. For detailed instructions
GPD Global | https://www.gpd-global.com/pdf/doc/Contour-Mapping-Calibration-User-Guide-221MAPDOC-5.pdf
lowered to accommodate the glass plate in STEP 4- Prepare Work Area (page 5). 4. Reboot the system. The message Modified Servo call for Glass Plate Mapping will no longer appear in the startup sequence. 5. Teach the Base Locations. For detailed instructions
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/last-will-of-bga-void.pdf
treated as a single resistance channel. An “event” was recorded if the resistance of a channel exceeded 300 for longer than 0.2 sec within a 30-second period. A failure was defined for a component when it: - Exceeded the maximum resistance for 15
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2022/04/last-will-of-bga-void-1.pdf
treated as a single resistance channel. An “event” was recorded if the resistance of a channel exceeded 300 for longer than 0.2 sec within a 30-second period. A failure was defined for a component when it: - Exceeded the maximum resistance for 15
| https://www.eptac.com/category/upcoming-webinars/shown.bs.collapse/page/6/__/ais-highlight__/%3C/em%3E/134.936%25/gtm.start/page/5/
. About Leo Lambert Leo Lambert has been the Vice President and Technical Director at EPTAC Corporation for over two decades, but a consummate contributor to the electronics industry and the IPC for much longer than that
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Dispense-System-Service-Guide-22290008G.pdf
FLOware Software Guide. X Conveyor belts If a conveyor is present, inspect belt tension. If necessary, adjust tension per ADJUST Conveyor Belt Tension (pg 5.23). Inspect length of both belts for grays and wear spots. Immediately replace excessively worn or
