GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Cyclops-II-Vision-Software-InstallUpdateRestore-Guide-22240108.pdf
right). Figure 4: USB license dongle (orange or green) plugged into rear panel of Cyclops II computer c. Verify the license number engraved on the Cyclops II Vision Software USB matches the license on the USB license dongle per USB (pg 2). 3. Power on the
GPD Global | https://www.gpd-global.com/pdf/doc/Cyclops-II-Vision-Software-InstallUpdateRestore-Guide-22240108.pdf
right). Figure 4: USB license dongle (orange or green) plugged into rear panel of Cyclops II computer c. Verify the license number engraved on the Cyclops II Vision Software USB matches the license on the USB license dongle per USB (pg 2). 3. Power on the
| https://unisoft-cim.com/test-fixture_download.htm
"Bed Of Nails" Test Fixture. In this step we will create the Circuit Description file that matches the "Bed Of Nails" Test Fixture for the ATE tester. The Unisoft software supports virtually all "Bed Of Nail" type In-Circuit testers such as Keysight
| https://ipcapexexpo.org/media/33/download
. As chief editor of IndustryWeek, Travis offers a unique perspective that matches this high-tech energy with insights from his daily contact with some of the world’s most successful and innovative manufacturers about real-life implementations
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Side-Mount-Loader-Unloader-Guide-24000600.pdf
- manually slide the substrate partially off of the conveyor toward the maga- zine so you can use it to visually align the slot with the conveyor. 5. To teach the first slot: a. Teach the FirstSlotPos value by jogging Z up/down until substrate height matches
GPD Global | https://www.gpd-global.com/pdf/doc/Side-Mount-Loader-Unloader-Guide-24000600.pdf
- manually slide the substrate partially off of the conveyor toward the maga- zine so you can use it to visually align the slot with the conveyor. 5. To teach the first slot: a. Teach the FirstSlotPos value by jogging Z up/down until substrate height matches
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Advanced-FPC-Real-Time-Controller-User-Guide-22940009.pdf
image that matches the currently selected dispense mode (dot or line) displays at the base of the reservoir: • Dot dispense mode = nozzle dispensing dots • Continuous/line dispense mode = nozzle dis- pensing a line Reservoir status (left to right) • Run
GPD Global | https://www.gpd-global.com/pdf/doc/Advanced-FPC-Real-Time-Controller-User-Guide-22940009.pdf
image that matches the currently selected dispense mode (dot or line) displays at the base of the reservoir: • Dot dispense mode = nozzle dispensing dots • Continuous/line dispense mode = nozzle dis- pensing a line Reservoir status (left to right) • Run
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20110505-PBT-002N-FORCEWare-v5-5-3.pdf
Calibrate Speed window matches the speed range on the speed dial hardware. Speeds will range either from 100 to 300 or from 100 to 600. b. If the maximum speed on the speed dial hardware is 600 mm, skip to step 4; otherwise, continue with step 3.c. 05/17/11
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20111117-PBT-002O-FORCEWare-v5-5-4.pdf
. Verify speeds: a. First, verify that the speed range shown in the Calibrate Speed window matches the speed range on the speed dial hardware. Speeds will range either from 100 to 300 or from 100 to 600. b. If the maximum speed on the speed dial hardware is
