ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/de-DE/divisions/polymer-processing-systems/news/news/2019-09-09
Dickenschwankungen, die laut Werksleiter Dipesh Patel „problemlos innerhalb des Toleranzbereichs liegt“. „Zudem brauchte unsere alte Düse nach dem Hochfahren der Anlage etwa zwei Stunden, um sich zu stabilisieren und Folien mit einem zulässigen Grad an
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/news/news/2019-09-09
“well within acceptable levels,” according to Dipesh Patel, director. “In addition, while our old die needed about two hours after line startup to stabilize and start producing film with an acceptable level of gauge variation, the new EDI die stabilizes within only 15 or 20 minutes
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/es-ES/divisions/polymer-processing-systems/news/news/2019-09-09
línea de películas de forma continua a 3.500 kg/h con una variación del calibre que se mantiene “dentro de niveles aceptables”, de acuerdo con Dipesh Patel, director
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/it-IT/divisions/polymer-processing-systems/news/news/2019-09-09
“molto di sotto dei livelli accettabili - come ha dichiarato l’amministratore Dipesh Patel, che ha aggiunto - e inoltre, mentre alla testa precedente occorrevano circa due ore
Surface Mount Technology Association (SMTA) | https://www.smta.org/chapters/chapters_detail.cfm?chapter_id=37
! President : Julio A. Estrada (STI Electronics, Inc.) Vice President : Chandradip Patel, Ph.D. (Amazon AWS) Secretary : Adrian Leal (The IPS group) Treasurer : Glen A Herzog (FairfieldNodal) Technical Advisor (Appointed) : Suriyakan Kleitz (Schlumberger
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/zh-CN/divisions/polymer-processing-systems/news/news/2019-09-09
需要停产 48 至 60 小时。该模头还出现了厚度偏差，只有将生产线速度限制在产量不超过每小时 2,800 千克的水平才能将这一偏差控制在可接受的范围内。 根据主管 Dipesh Patel 的介绍，自 2019 年 2 月安装依迪埃 ® 模头以来， Asia Poly Films 的生产线就一直以每小时产量 3,500 千克的速度持续运行，厚度偏差也很好地保持在了 “ 远在可接受的范围内 ” 。 “ 除此之外，我们原先的模头在生产线启动后需要大约两小时才能稳定下来，开始生产出厚度偏差处于可接受范围内的薄膜，而新的依迪埃模头在短短 15 或 20 分钟内就能稳定下来。 ” Patel 先生表示，在保持原有挤出机、控制器和聚合物配方不变的同时使用新款 Extrusion Dies Industries
Surface Mount Technology Association (SMTA) | https://www.smta.org/iceet/2019_ICEET_Program.pdf
, Ph.D., David Bernard Consultancy To Bake or Not to Bake? Large Metallic BGAs in Sealed ESD Bags with no Indication of Humidity Exposure Bihari Patel, Microart Services Inc
Surface Mount Technology Association (SMTA) | https://www.smta.org/directory/consultants.cfm
&LS, LLC 5 Homestead Drive Trabuco Canyon, CA 92679 949-713-7229 kathyp@palsrvs.com http://www.palsrvs.com/ Categories 2-8, 10-22, 24 Bihari Patel
Surface Mount Technology Association (SMTA) | https://www.smta.org/membership/ambassador.cfm
Components Kathy Palumbo CEO PA&LS, LLC Pratish Patel CTO & EMS Business Developer Electronic Interconnect Carol Primdahl Retired Scott Priore Senior Manager, Mfg
Surface Mount Technology Association (SMTA) | https://www.smta.org/chapters/chapters_detail.cfm?chapter_id=35
.) SMTA Liaison : Yeunjih Wang Membership Committee (Appointed) : Daniel Morales (Legacy Precision LLC) Programs Committee (Appointed) : Surendra K. Patel Ph.D. (Renprotech Solutions LLC) Programs Committee (Appointed) : Akhil Singh 32043 (NXP
.png)
