805 rev on drawing results

PCB Libraries Forum : Making a Donut Pad Shape in Allegro

PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_making-a-donut-pad-shape-in-allegro_topic1141.xml

; Pick both of the arcs and the lines, then click right mouse button and select Complete.Right mouse click and select Done.8. Now select Setup > Design Parameters and on the 'Design' tab set the Drawing Type to Shape

PCB Libraries, Inc.

PCB Libraries Forum : 2D Line Assembly Pads

PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_2d-line-assembly-pads_topic1815.xml

. It's for an assembly drawing. What other option is there? 2D Line Assembly Pads : When did BGA pads on assembly... Author: AGONZ67Subject: 1815Posted: 08 Jan 2016 at 2:46pmWhen did BGA pads on assembly become 2D Lines

PCB Libraries, Inc.

PCB Libraries Forum : 2 Pad Chips With Different Lead Length

PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_2-pad-chips-with-different-lead-length_topic1988.xml

. However, I am unable to do the same with components that have different lead lengths.I.E. the "T" value in the drawing below are different and have different tolerances on either side of the

PCB Libraries, Inc.

Post Lead Trimming Reflow Requirements - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/ask-helena-leo/ask/post-lead-trimming-reflow-requirements

., break away tie bars. Additionally Rev E also provide this picture: The requirement as defined by Class 3, is when the solder joint is cut into such as the illustration on the left, it must be reflowed regardless of whether or not it was inspected at 10x

J-STD-001FS Space Addendum Module 6 Certificate - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/ask/j-std-001fs-space-addendum-module-6-certificate/

? They all currently have a valid certificate in the J-STD-001 plus 1 other module. I have a training report to fill out after they pass and it says to put the certificate number on there

Edge Connector Graphics - PCB Libraries Forum

PCB Libraries, Inc. | https://www.pcblibraries.com/forum/edge-connector-graphics_topic2011_post8269.html

V2017.02 pre-release that will be uploaded later today. Change the text "Polarity Symbol" to "Drafting Symbols" Add Legend Bottom Add Assembly Drawing Bottom Stay connected - follow us

PCB Libraries, Inc.

Edge Connector Graphics - PCB Libraries Forum

PCB Libraries, Inc. | https://www.pcblibraries.com/forum/edge-connector-graphics_topic2011_post8266.html

    Posted: 10 Nov 2016 at 10:12am I have an EDGE connector that protrudes into the board on both the top and the bottom of PWB. How do I add graphics

PCB Libraries, Inc.

Edge Connector Graphics - PCB Libraries Forum

PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/edge-connector-graphics_topic2011.html

V2017.02 pre-release that will be uploaded later today. Change the text "Polarity Symbol" to "Drafting Symbols" Add Legend Bottom Add Assembly Drawing Bottom Stay connected - follow us

PCB Libraries, Inc.

Edge Connector Graphics - PCB Libraries Forum

PCB Libraries, Inc. | https://www.pcblibraries.com/forum/edge-connector-graphics_topic2011_post8264.html

V2017.02 pre-release that will be uploaded later today. Change the text "Polarity Symbol" to "Drafting Symbols" Add Legend Bottom Add Assembly Drawing Bottom Stay connected - follow us

PCB Libraries, Inc.

Zero Component Orientation for undefined types - PCB Libraries Forum

PCB Libraries, Inc. | https://www.pcblibraries.com/forum/zero-component-orientation-for-undefined-types_topic3027.html

. I have decided to just list which footprint types are Zero Component Orientation compliant on the assembly drawing. I don't expect answers to these problems, but I will list them in the hope you have some influence on the committees or that someone who does reads this forum. Pin 1

PCB Libraries, Inc.