44 saponifier remove no clean flux results

Issues of Burnt Flux on Class 3 PCB Assemblies | EPTAC

| https://www.eptac.com/soldertips/issues-of-burnt-flux-on-class-3-pcb-assemblies/

. I understand that if the laminate is burnt it is a defect condition, but I am not clear on burnt flux for a no-clean process. Any clarification would be appreciated. Answer

Excess Flux Causing Intermittent Connection Issues - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/ask-helena-leo/ask/excess-flux-causing-intermittent-connection-issues

: We are having an issue with the cleanliness of flux. The excess no-clean flux is located in an Ethernet port connector. The units pass all tests with no issues, however

SolderTip #44: IPC Guidelines for Flux Selection and Use | EPTAC

| https://www.eptac.com/soldertips/soldertip-44-ipc-guidelines-for-flux-selection-and-use/

.  The answer is NO, IPC will not provide information as to which flux one should use as it does not know the functionality of the board or the product.  IPC will, however

Issues of Burnt Flux on Class 3 PCB Assemblies - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/soldertip/issues-of-burnt-flux-on-class-3-pcb-assemblies/

. I understand that if the laminate is burnt it is a defect condition, but I am not clear on burnt flux for a no-clean process. Any clarification would be appreciated. Answer

Issues of Burnt Flux on Class 3 PCB Assemblies - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/soldertips/soldertip/issues-of-burnt-flux-on-class-3-pcb-assemblies

. I understand that if the laminate is burnt it is a defect condition, but I am not clear on burnt flux for a no-clean process. Any clarification would be appreciated. Answer

SolderTip #44: IPC Guidelines for Flux Selection and Use - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/soldertip/soldertip-44-ipc-guidelines-for-flux-selection-and-use/

: Through Hole Soldering of Thick PCBs SolderTip #38: Clean vs No-Clean Fluxes SolderTip #39: Class 2 vs Class 3 Assemblies SolderTip #40: Component Mounting and Acceptability Question

SolderTip #44: IPC Guidelines for Flux Selection and Use - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/soldertips/soldertip/soldertip-44-ipc-guidelines-for-flux-selection-and-use

.  The answer is NO, IPC will not provide information as to which […]     Question :  Does the IPC have guidelines or recommendations on flux selection and use? Answer

(cont.) •  Q:  If  using  low  solid  flux  (no  clean)  was  the  flux   heat  acclean  up  the  light  oxida

| https://www.eptac.com/wp-content/uploads/2014/05/eptac_06_18_14.pdf

S3X58-HF1100-3 - 600 gm - PCBASupplies

| https://pcbasupplies.com/s3x58-hf1100-3-600gm/

. Flux Coagulation Technique Improves First Pass Yield The flux formulation of S3X58-HF1100-3 type 4 no clean solder paste is specifically designed to exhibit enhanced flux coagulation at the time when

SolderTips: Solderability Issues with Nickle Plated Surfaces - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/soldertip/soldertips-solderability-issues-with-nickle-plated-surfaces/

: Wave Soldering Insufficient Fill and Voids in PTH SolderTip #37: Through Hole Soldering of Thick PCBs SolderTip #38: Clean vs No-Clean Fluxes SolderTip #39