454 solder wave tub wont heat up results

High Quality SMT Reflow Oven Machine for LED PCB Soldering-Reflow oven-Reflow oven,SMT Reflow Solder

| http://etasmt.com:9060/te_product_j/2019-07-10/3428.chtml

Air Reflow Oven,SMT Reflow Machine,SMT Reflow Oven Manufacturers,Lead free Solder Reflow,LED Reflow Oven,Ir Reflow Machine,Lead free Reflow Oven SMT Line Wave Soldering SAMSUNG/Hanwha SMT Machine

High Quality SMT Reflow Oven Machine for LED PCB Soldering-Reflow oven-Reflow oven,SMT Reflow Solder

| http://etasmt.com/te_product_j/2019-07-10/3428.chtml

Air Reflow Oven,SMT Reflow Machine,SMT Reflow Oven Manufacturers,Lead free Solder Reflow,LED Reflow Oven,Ir Reflow Machine,Lead free Reflow Oven SMT Line Wave Soldering JUKI SMT Pick and Place Machine

SolderTips | EPTAC

| https://www.eptac.com/solder-tips/

. Does turning up the solder pot too high cause impurities to collect on parts? Can you comment on this? Read Answer What’s with the expiration dates on solder paste or wire? Question

. 16 #4 Wave Soldering LCDs  Selective wave or mass soldering system  Use of spacers to keep the unit up off the board surface  Double sided board would not require too much top side preheat to get the solder to flow up into the plated through hole 17 Upcoming Webinars New Webinars added every month. Check back at: http

| https://www.eptac.com/wp-content/uploads/2021/11/webinar_eptac_09_17_08.pdf

Reliability of Reworked Lead-free Assemblies - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/ask-helena-leo/ask/reliability-of-reworked-lead-free-assemblies

. The intent is based upon IPC-4101 and whether or not leaded solder or lead-free solder is being used. You state “…Our present process: 2 heat excursions, thru reflow, 2 thru wave, one thru rework

Vitronics AlphaWave

1st Place Machinery Inc. | http://www.firstplacemachinery.com/first_place_smt_pcb_wave_solder_vitronics.html

) Heat-up Time of Solder Bath: Approx. 2.5 hours to reach 250 degrees c (482 degrees F) for eutectic 63/37 solder, by 3 heating elements (1 kW each

1st Place Machinery Inc.

SolderTip #37: Through Hole Soldering of Thick PCBs - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/soldertip/soldertip-37-through-hole-soldering-of-thick-pcbs/

. More than likely, there is not enough heat or thermal capacity in the solder iron to heat the entire hole up to soldering temperatures, thereby the solder solidifies going up through the hole and that’s it, it doesn’t fill any further

: –  oxidation of the tip plating – Use of very small solder wire. •  Solder will ball up on a dewetted tip •  Heat transfer is also impacted with a dewetted tip 7 Tip Care Practices To Prevent and Reduce Dewetting

| https://www.eptac.com/wp-content/uploads/2014/11/eptac_11_19_14.pdf

Reliability of Reworked Lead-free Assemblies - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/ask/reliability-of-reworked-lead-free-assemblies/

. The intent is based upon IPC-4101 and whether or not leaded solder or lead-free solder is being used. You state “…Our present process: 2 heat excursions, thru reflow, 2 thru wave, one thru rework

Which Soldering Defects are Related to the Incorrect Setup of the Reflow Profile?-SMT Technical-Refl

| http://etasmt.com:9060/te_news_industry/2021-08-31/23964.chtml

– ramp up too fast Same as soldering ball. Poor wetting – ramp up too slow Solder paste is oxidizing if the pre-heat too long. Pre-heat and soak zone (from 150°C to 180°C