PCB Libraries, Inc. | https://www.pcblibraries.com/forum/copper-on-one-side-of-through-hole_topic1972.html
. I've tried plated and non-plated hole but with same results. I know I can put some copper on the top layer but I'd like to figure this out in case I come across a case where that's not an option
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic1972&OB=ASC.html
. I've tried plated and non-plated hole but with same results. I know I can put some copper on the top layer but I'd like to figure this out in case I come across a case where that's not an option
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/offset-defined-in-padstack-to-match-corporate-grid_topic2726_post11061.html
. Smallest placement grid I've use is 0,05mm which is almost twice the line width you will use on a board without having to pay for a premium from most pcb fab house and even then, line width can vary
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/offset-defined-in-padstack-to-match-corporate-grid_topic2726.html
. Smallest placement grid I've use is 0,05mm which is almost twice the line width you will use on a board without having to pay for a premium from most pcb fab house and even then, line width can vary
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/pads-layout-v2005-export-to-diptrace_topic1329.html
Plib_ASCII.pdf, I think the last number in the line "COPCLS 10 0.01 1 20" is the linestyle, which should be either -1 or 0. Is this right? Setting the last number 20 to -1 causes DipTrace to come up with a memory exception though
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/pads-layout-v2005-export-to-diptrace_topic1329_post5270.html
9.0" says the angles are in 1/10 of a degree. What is correct for V2005.0? Referring to the V2005.0 spec, the last number in the line "COPCLS 10
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/pads-layout-v2005-export-to-diptrace_topic1329_post5265.html
9.0" says the angles are in 1/10 of a degree. What is correct for V2005.0? Referring to the V2005.0 spec, the last number in the line "COPCLS 10
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic1329&OB=DESC.html
Plib_ASCII.pdf, I think the last number in the line "COPCLS 10 0.01 1 20" is the linestyle, which should be either -1 or 0. Is this right? Setting the last number 20 to -1 causes DipTrace to come up with a memory exception though
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic1329&OB=ASC.html
9.0" says the angles are in 1/10 of a degree. What is correct for V2005.0? Referring to the V2005.0 spec, the last number in the line "COPCLS 10
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/offset-defined-in-padstack-to-match-corporate-grid_topic2726_post11054.html
. Smallest placement grid I've use is 0,05mm which is almost twice the line width you will use on a board without having to pay for a premium from most pcb fab house and even then, line width can vary
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
.gif)
winsouce.jpg)