Technical Library: 1

IMPACT OF 0201 COMPONENTS ON CURRENT MANUFACTURING SYSTEMS

Technical Library | 2023-05-02 19:16:57.0

1.5 with a 150μm specification window. For 0201 components, the minimum requirement is CpK > 2.0 with a 100μm specification window. The spec window may need to be reduced down to 75μm if the controls for high volume manufacturing are insufficient. Also directly impacting the placement quality is the ability to apply sufficient solder consistently to the board. The goal is to maintain current printing practices, but the effect of powder size will be examined. This paper will evaluate the impact of placement accuracy and solder powder size on 0201 manufacturing quality.

Motorola Mobility LLC.

Exceptional Optoelectronic Properties of Hydrogenated Bilayer Silicene

Technical Library | 2015-03-19 20:33:34.0

Silicon is arguably the best electronic material, but it is not a good optoelectronic material. By employing first-principles calculations and the cluster-expansion approach, we discover that hydrogenated bilayer silicene (BS) shows promising potential as a new kind of optoelectronic material. Most significantly, hydrogenation converts the intrinsic BS, a strongly indirect semiconductor, into a direct-gap semiconductor with a widely tunable band gap. At low hydrogen concentrations, four ground states of single- and double sided hydrogenated BS are characterized by dipole-allowed direct (or quasidirect) band gaps in the desirable range from 1 to 1.5 eV, suitable for solar applications. At high hydrogen concentrations, three well-ordered double-sided hydrogenated BS structures exhibit direct (or quasidirect) band gaps in the color range of red, green, and blue, affording white light-emitting diodes. Our findings open opportunities to search for new silicon-based light-absorption and light-emitting materials for earth-abundant, high efficiency, optoelectronic applications.Originally published by the American Physical Society

Oak Ridge National Laboratory

Dissolution in Service of the Copper Substrate of Solder Joints

Technical Library | 2019-06-20 00:09:49.0

It is well known that during service the layer of Cu6Sn5 intermetallic at the interface between the solder and a Cu substrate grows but the usual concern has been that if this layer gets too thick it will be the brittleness of this intermetallic that will compromise the reliability of the joint, particularly in impact loading. There is another level of concern when the Cu-rich Cu3Sn phase starts to develop at the Cu6Sn5/Cu interface and an imbalance in the diffusion of atomic species, Sn and Cu, across that interface results in the formation at the Cu3Sn/Cu interface of Kirkendall voids, which can also compromise reliability in impact loading. However, when, as is the case in some microelectronics, the copper substrate is thin in relation to the volume of solder in the joint an overriding concern is that all of the Cu will be consumed by reaction with Sn to form these intermetallics.This paper reports an investigation into the kinetics of the growth of the interfacial intermetallic, and the consequent reduction in the thickness of the Cu substrate in solder joints made with three alloys, Sn-3.0Ag-0.5Cu, Sn-0.7Cu-0.05Ni and Sn-1.5Bi-0.7Cu-0.05Ni.

Nihon Superior Co., Ltd.

Creep Corrosion of PWB Final Finishes: Its Cause and Prevention

Technical Library | 2021-04-08 00:30:49.0

As the electronic industry moves to lead-free assembly and finer-pitch circuits, widely used printed wiring board (PWB) finish, SnPb HASL, has been replaced with lead-free and coplanar PWB finishes such as OSP, ImAg, ENIG, and ImSn. While SnPb HASL offers excellent corrosion protection of the underlying copper due to its thick coating and inherent corrosion resistance, the lead-free board finishes provide reduced corrosion protection to the underlying copper due to their very thin coating. For ImAg, the coating material itself can also corrode in more aggressive environments. This is an issue for products deployed in environments with high levels of sulfur containing pollutants encountered in the current global market. In those corrosive environments, creep corrosion has been observed and led to product failures in very short service life (1-5 years). Creep corrosion failures within one year of product deployment have also been reported. This has prompted an industry-wide effort to understand creep corrosion

Alcatel-Lucent

  1  

1,5 searches for Companies, Equipment, Machines, Suppliers & Information

Win Source Online Electronic parts

Software for SMT placement & AOI - Free Download.
Circuit Board, PCB Assembly & electronics manufacturing service provider

Best Reflow Oven
PCB Handling with CE

Smt Feeder repair service centers in Europe, North, South America
IPC Training & Certification - Blackfox

Wave Soldering 101 Training Course
PCB separator

Internet marketing services for manufacturing companies