Technical Library | 2019-05-24 09:22:59.0
There is a smaller process window and a much narrower margin of error when creating and using lead-free reflow profiles for surface mount parts on printed circuit boards (PCBs). Solder balls, dewetting, tombstones, voids, and head-on-pillow problems will occur much more frequently because lead-free alloys behave differently than eutectic pastes. Problems are compounded due to the extra heat necessary for some lead-free pastes to reach their melting points.
Technical Library | 2019-06-17 15:09:43.0
Very often pick and place machines are programmed using CAD data. This data increases the accuracy, precision, and repeatability of its component placement objectives. CAD data makes fine pitch and small component assemblies repeatable, but cannot adjust to a particular board unless it is exactly the same size and shape of the original board used for programming. The process by which printed circuit boards (PCBs) are made only allows some minor changes inboard size and shape, but these small differences are enough for parts to be misplaced. For this reason we use fiducial marks to increase the chances of precise component alignment.
Technical Library | 2019-05-23 10:42:00.0
Why identify flux residues? The primary purpose of flux is to reduce species of metal oxides from solderable surfaces, and to act as a mechanism for lifting and removing debris. If the assembly is not properly cleaned after manufacturing, flux may continue to reduce metals and may eventually corrode the assembly. When the assembly is powered, the metal ions may precipitate along electromagnetic field lines and form dendritic shorts. In addition, the presence of residue can alter the insulation properties of a board, affect the adhesion of the conformal coating, or interfere with the moving parts of the assembly. In radio frequency (RF) applications, flux may change the RF properties on the surface of the printed circuit board (PCB) such as the dielectric strength, surface resistance, and Q-resonance.
Technical Library | 2020-03-09 10:50:17.0
A customer called the Helpline seeking advice for cleaning no-clean fluxes prior to applying a conformal coating. The customer's assemblies were manufactured with a no-clean rosin based solder paste (ROL0) and were cleaned with an isopropyl alcohol (IPA) wash. After cleaning, a white residue was sometimes found in areas with high paste concentrations and was interfering with the adhesion of the conformal coating (Figure 1). For conformal coatings to adhere properly, the printed circuit board (PCB) surface must be clean of fluxes and other residues. In addition, ionic contamination left by flux residues can lead to corrosion and dendrite growth, two common causes of electronic opens and shorts. Other residues can lead to unwanted impedance and physical interference with moving parts.
Technical Library | 2023-03-13 19:35:47.0
Translational Research in Additive Manufacturing at GTMI * Additive manufacturing/3D printing process and equipment development (e.g., metal, polymer and composites part manufacturing) * Computational modeling and simulation of additive manufacturing/printed electronics processes * Advanced materials development for additive manufacturing/printed electronics * Application development and demonstration of additive manufacturing/printed electronics
Technical Library | 2023-06-02 14:13:02.0
This work examines the use of dual-material fused filament fabrication for 3D printing electronic componentsand circuits with conductive thermoplastic filaments. The resistivity of traces printed fromconductive thermoplastic filaments made with carbon-black, graphene, and copper as conductive fillerswas found to be 12, 0.78, and 0.014 ohm cm, respectively, enabling the creation of resistors with valuesspanning 3 orders of magnitude. The carbon black and graphene filaments were brittle and fracturedeasily, but the copper-based filament could be bent at least 500 times with little change in its resistance.Impedance measurements made on the thermoplastic filaments demonstrate that the copper-based filamenthad an impedance similar to a copper PCB trace at frequencies greater than 1 MHz. Dual material3D printing was used to fabricate a variety of inductors and capacitors with properties that could bepredictably tuned by modifying either the geometry of the components, or the materials used to fabricatethe components. These resistors, capacitors, and inductors were combined to create a fully 3Dprinted high-pass filter with properties comparable to its conventional counterparts. The relatively lowimpedance of the copper-based filament enabled its use for 3D printing of a receiver coil for wirelesspower transfer. We also demonstrate the ability to embed and connect surface mounted components in3D printed objects with a low-cost ($1000 in parts), open source dual-material 3D printer. This work thusdemonstrates the potential for FFF 3D printing to create complex, three-dimensional circuits composedof either embedded or fully-printed electronic components.
Technical Library | 2020-09-16 21:24:56.0
Additive manufacturing processes typically used for mechanical parts can be combined with enhanced technologies for electronics production to enable a highly flexible manufacturing of personalized 3D electronic devices. To illustrate different approaches for implementing electrical and electronic functionality, conductive paths and electronic components were embedded in a powder bed printed substrate using an enhanced 3D printer. In addition, a modified Aerosol Jet printing process and assembly technologies adapted from the technology of Molded Interconnect Devices were applied to print circuit patterns and to electrically interconnect components on the surface of the 3D substrates.
Institute for Factory Automation and Production Systems (FAPS)
Technical Library | 2020-09-16 21:20:37.0
3D printing is disrupting the design and manufacture of electronic products. 3D printing electronics offers great potential to build complex object with multiple functionalities. Particularly, it has shown the unique ability to make embedded electronics, 3D structural electronics, conformal electronics, stretchable electronics, etc. 3D printing electronics has been considered as the next frontier in additive manufacturing and printed electronics. Over the past five years, a large number of studies and efforts regarding 3D printing electronics have been carried out by both academia and industries. In this paper, a comprehensive review of recent advances and significant achievements in 3D printing electronics is provided. Furthermore, the prospects, challenges and trends of 3D printing electronics are discussed. Finally, some promising solutions for producing electronics with 3D printing are presented.
Technical Library | 2016-05-30 22:24:00.0
As a part of series of studies on X-Ray inspection technology to quantify solder defects in BGA balls, we have conducted inspection of 3 level POP package by using a new AXI that capable of 3D-CT imaging. The new results are compared with the results of earlier AXI measurements. It is found that 3D measurements offer better defect inspection quality, lower false call and escapes.
Technical Library | 2018-10-10 21:26:52.0
Printed electronics is a familiar term that is taking on more meaning as the technology matures. Flexible electronics is sometimes referred to as a subset of this and the printing approach is one of the enabling factors for roll to roll processes. Printed electronics is improving in performance and has many applications that compete directly with printed circuit boards. The advantage of roll to roll is the speed of manufacturing, the large areas possible, and a reduction in costs. As this technology continues to mature, it is also merging with the high profile 3D printing. (...)This paper will show working demonstrations of printed circuit structures, the obstacles, and the potential future of 3D printed electronics.
