Technical Library | 2020-10-14 14:18:13.0
Thermally conductive adhesives provide many advantages over traditional mechanical fastening techniques. Specifically, they use less material and space and are more amenable to automation than existing solutions. The thermal and mechanical properties of these materials are well understood but little work has been done to characterize and understand their toughness and fracture behavior. This paper presents the effects of filler loading as well as matrix composition on the fracture toughness of thermally conductive silicone adhesives. It was observed that the fracture toughness of these materials increased significantly with initial filler loading, and that the mechanical properties and fracture toughness depended on the molecular architecture of the matrix used.
Technical Library | 2020-09-30 19:23:47.0
There is an increase in the number of optical sensors and cameras being integrated into electronics devices. These go beyond cell phone cameras into automotive sensors, wearables, and other smart devices. The applications can be lens bonding, waveguide imprinting, or other applications where the adhesive is in the optical pathway. To support these various optical applications, new materials with tailorable optical properties are required. There is often a mismatched refractive index between plastic lenses such as PC (Poly Carbonate), COP (Cyclo Olefin Polymer), COC (Cyclo Olefin Copolymer), PMMA (Poly Methyl Methacrylate), and UV curable liquid adhesive. A UV curable liquid adhesive is needed where you can alter the refractive index from 1.470 to 1.730, and maintain high optical performance as yellowness index, haze, and transmittance. This wide range of refractive index possibilities provides optimized optical design. Using particular plastic lens must consider how chemical attack is occurring during the process. Another consideration is that before the UV curable liquid adhesive is cured, chemical raw component can attack the plastic lens which then cracks and delaminates. We will also show engineering and reliability data which defined root cause and provided how optical performance is maintained under different reliability conditions.
Technical Library | 2020-12-24 02:50:56.0
A method for packaging integrated circuit silicon die in thin flexible circuits has been investigated that enables circuits to be subsequently integrated within textile yarns. This paper presents an investigation into the required materials and component dimensions in order to maximize the reliability of the packaging method. Two die sizes of 3.5 mm×8 mm× 0.53 mm and 2 mm×2 mm×0.1 mm have been simulated and evaluated experimentally under shear load and during bending. The shear and bending experimental results show good agreement with the simulation results and verify the simulated optimal thickness of the adhesive layer. Three underfill adhesives (EP30AO, EP37-3FLF, and Epo-Tek 301 2fl), three highly flexible adhesives (Loctite 4860, Loctite 480, and Loctite 4902), and three substrates (Kapton,Mylar, and PEEK) have been evaluated, and the optimal thickness of each is found. The Kapton substrate, together with the EP37-3FLF adhesive, was identified as the best materials combination with the optimum underfill and substrate thickness identified as 0.05 mm.
Technical Library | 2021-08-11 00:52:35.0
Formulators of multi-component adhesives, potting and encapsulation materials are careful not to supply products with entrapped air. They do this by manufacturing under vacuum or degassing them before supplying to the end user. Consequently, entrapped air in a mixed material is usually a processing issue.
Technical Library | 2022-01-26 15:22:33.0
Reliability of conformal coatings used to mitigate tin whisker growth depends on their ability to contain tin whiskers. Two key material properties required to assess the reliability of a polyurethane coating are documented experimentally: adhesion strength and puncture strength. A modified blister test using a predefined blister area is employed to assess the adhesion strength and a puncture test is employed to evaluate the puncture strength of the coating. After measuring the properties at time zero, the coatings are subjected to accelerated testing conditions (high temperature/humidity storage and temperature cycling) and the degradations of the coating properties are documented.
Technical Library | 2016-11-17 14:37:41.0
With increasing LED development and production, thermal issues are becoming more and more important for LED devices, particularly true for high power LED and also for other high power devices. In order to dissipate the heat from the device efficiently, Au80Sn20 alloy is being used in the industry now. However there are a few drawbacks for Au80Sn20 process: (1) higher soldering temperature, usually higher than 320°C; (2) low process yield; (3) too expensive. In order to overcome the shortcomings of Au80Sn20 process, YINCAE Advanced Materials, LLC has invented a new solderable adhesive – TM 230. Solderable adhesives are epoxy based silver adhesives. During the die attach reflow process, the solder material on silver can solder silver together, and die with pad together. After soldering, epoxy can encapsulate the soldered interface, so that the thermal conductivity can be as high as 58 W/mk. In comparison to Au80Sn20 reflow process, the solderable adhesive has the following advantages: (1) low process temperature – reflow peak temperature of 230°C; (2) high process yield – mass reflow process instead of thermal compression bonding process; (3) low cost ownership. In this paper we are going to present the die attach process of solderable adhesive and the reliability test. After 1000 h lighting of LED, it has been found that there is almost no decay in the light intensity by using solderable adhesive – TM 230.
Technical Library | 2016-11-09 19:22:54.0
Nordson MARCH found a solution for a manufacturer of PCBAs used in ruggedized environments. Read how plasma prior to conformal coating reduced defects and virtually eliminated coating-related failures.
Technical Library | 2018-12-26 10:31:05.0
The development of novel interconnection materials for production of electronics is of considerable interest to fulfill increasing demands on interconnect reliability in increasingly demanding environments with respect to temperature extremes, mechanical stresses and/or production limitations. Adhesives are playing an increasingly significant role in the continuously evolving electronics industry. (...)Specific applications will be presented that highlight the feasibility of the technology with respect to conductivity, structural reliability and lifetime standards. The deposition of the novel ICA has been performed using a jet printing technology to ensure both precise and accurate positioning, size and volume delivery.
Technical Library | 2018-04-18 23:55:01.0
Higher functionality, higher performance and higher reliability with smaller real estate are the mantras of any electronic device and the future guarantees more of the same. In order to achieve the requirements of these devices, designs must incorporate fine line and via pitch while maintain good circuitry adhesion at a smooth plating-resin interface to improve signal integrity. The Semi-Additive Process (SAP) is a production-proven method used on low dielectric loss tangent (Df) build-up materials that enables the manufacture of ultra-fine circuitry. (...) This paper will discuss a new SAP process for low loss build-up materials with low desmear roughness (Ra= 40-100 nm) and excellent adhesion (610-680 gf/cm) at various processing conditions. Along with the process flow, the current work will also present results and a discussion regarding characterization on the morphology and composition of resin and/or metal plating surfaces using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX), surface roughness analysis, plating-resin adhesion evaluation from 90o peel tests
Technical Library | 2016-01-12 11:07:56.0
With the increasing demand of device miniaturization, high speed, more memory, more function, low cost, and more flexibility in device design and manufacturing chain, YINCAE has published a white paper on a first individual solder joint encapsulant which can eliminate underfilling process with at least five times solder joint increase and provide more flexibility for fine pitch and high density application. In order to meet the demand of manufacturing of high speed and low cost, YINCAE has invented a room temperature stable and jettable solder joint encapsulant adhesive – SMT 266. The invention of SMT 266 has allowed our customers to have more flexibility in their high-speed production line such as worry free on the work life of adhesive and workable jetting process.
.png)
