Technical Library: any (Page 6 of 10)

Printing and Curing of Conductive Ink Track on Curvature Substrate using Fluid Dispensing System and Oven

Technical Library | 2017-12-21 11:24:05.0

The present work concerns on the use of sensors to monitor the structural health of wind turbine . Conventionally the inspection was made using non-contact sensing during the turbine’s inoperable period hence loss occurred. A real -time monitoring system via embedded wireless sensor is preferred but the sensor could only be implanted using non-contact printing method due to most turbine blade s’ curved surface. Conductive ink associate d with non-contact printing method via fluid dispensing system are proposed since conductive inks are proven stretchable and fluid dispensing system enables printing on various substrates and works well with any materials...

University of Tun Hussein Onn

Advanced Cu Electroplating Process for Any Layer Via Fill Applications with Thin Surface Copper

Technical Library | 2019-06-26 23:21:49.0

Copper-filled micro-vias are a key technology in high density interconnect (HDI) designs that have enabled increasing miniaturization and densification of printed circuit boards for the next generation of electronic products. Compared with standard plated through holes (PTHs) copper filled vias provide greater design flexibility, improved signal performance, and can potentially help reduce layer count, thus reducing cost. Considering these advantages, there are strong incentives to optimize the via filling process. This paper presents an innovative DC acid copper via fill formulation, for VCP (Vertical Continues Plating) applications which rapidly fills vias while minimizing surface plating.

MacDermid Inc.

Approaches to Overcome Nodules and Scratches on Wire Bondable Plating on PCBs

Technical Library | 2020-08-27 01:22:45.0

Initially adopted internal specifications for acceptance of printed circuit boards (PCBs) used for wire bonding was that there were no nodules or scratches allowed on the wirebond pads when inspected under 20X magnification. The nodules and scratches were not defined by measurable dimensions and were considered to be unacceptable if there was any sign of a visual blemish on wire-bondable features. Analysis of the yield at a PCB manufacturer monitored monthly for over two years indicated that the target yield could not be achieved, and the main reasons for yield loss were due to nodules and scratches on the wirebonding pads. The PCB manufacturer attempted to eliminate nodules and scratches. First, a light-scrubbing step was added after electroless copper plating to remove any co-deposited fine particles that acted as a seed for nodules at the time of copper plating. Then, the electrolytic copper plating tank was emptied, fully cleaned, and filtered to eliminate the possibility of co-deposited particles in the electroplating process. Both actions greatly reduced the density of the nodules but did not fully eliminate them. Even though there was only one nodule on any wire-bonding pad, the board was still considered a reject. To reduce scratches on wirebonding pads, the PCB manufacturer utilized foam trays after routing the boards so that they did not make direct contact with other boards. This action significantly reduced the scratches on wire-bonding pads, even though some isolated scratches still appeared from time to time, which caused the boards to be rejected. Even with these significant improvements, the target yield remained unachievable. Another approach was then taken to consider if wire bonding could be successfully performed over nodules and scratches and if there was a dimensional threshold where wire bonding could be successful. A gold ball bonding process called either stand-off-stitch bonding (SSB) or ball-stitch-on-ball bonding (BSOB) was used to determine the effects of nodules and scratches on wire bonds. The dimension of nodules, including height, and the size of scratches, including width, were measured before wire bonding. Wire bonding was then performed directly on various sizes of nodules and scratches on the bonding pad, and the evaluation of wire bonds was conducted using wire pull tests before and after reliability testing. Based on the results of the wire-bonding evaluation, the internal specification for nodules and scratches for wirebondable PCBs was modified to allow nodules and scratches with a certain height and a width limitation compared to initially adopted internal specifications of no nodules and no scratches. Such an approach resulted in improved yield at the PCB manufacturer.

Teledyne DALSA

XRF- A Reality Check

Technical Library | 2008-08-14 20:48:12.0

The Restriction of Hazardous Substances (RoHS) regulations of the European Union, and similar regulations being enacted around the world, require the virtual elimination of lead (Pb), mercury (Hg), cadmium (Cd), hexavalent chromium (Cr6), polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE) from electronic products. Allowable concentration levels in any homogeneous material contained within a product are extremely low: 0.01% for Cd and 0.1% for other substances by weight. The most significant issue affecting the practical validation of RoHS compliance in the day-to-day assembly environment is ensuring that no restricted substances, especially tin-lead (SnPb) materials, have inadvertently entered into the production stream.

RMD Instruments

New Life for Aging Electronic Products

Technical Library | 2008-10-01 13:03:00.0

Many Original Equipment Manufacturers, (OEM’s), struggle to continue shipping aging or obsolete electronic products. Electronic products designed five to ten years ago are still relevant in the marketplace. Often these venerable old products have gained particular acceptance amongst a select group of customers. In many cases these old products fulfill a need in a unique manner. Examples include: designs that are grandfathered into an application due to regulatory considerations; designs having unique form-fit-and-function; designs running special software ; designs subject to contractual support and service requirements; designs in which a new contract stipulates delivery of older gear as part of a larger system offering. Any one or all of these reasons can lead an OEM to continue the production of electronic equipment well into its end of useful component life

Orchid Technologies Engineering & Consulting, Inc.

Advances in Conductive Inks across Multiple Applications and Deposition Platforms

Technical Library | 2012-12-27 14:35:29.0

Printed Electronics is generally defined as the patterning of electronic materials, in solution form, onto flexible substrates, omitting any use of the photolithography, etching, and plating steps commonly found within the Printed Circuit Board (PCB) industry. The origins of printed electronics go back to the 1960s, and close variants of several original applications and market segments remain active today. Through the 1980s and 1990s Printed Electronic applications based on Membrane Touch Switch and Electroluminescent lighting technologies became common, and the screen printed electronic materials used then have formed the building blocks for many of the current and emerging technologies and applications... First published in the 2012 IPC APEX EXPO technical conference proceedings.

DuPont

Radar Control Terminal (RCT) units

Technical Library | 2015-01-26 15:30:00.0

In 2005 Raytheon Technical Services Company, now Raytheon Information, Intelligence and Services (Raytheon IIS), approached Ensil regarding the repair of their manufactured Radar Control Terminal (RCT) units. The RCT TRS P/N 13563090-2, a key component in the AN/MPQ-64 Sentinel System, consisted of outdated parts which caused minor to major unit failures. Ensil repaired the RCT's at every turn, correcting any component with the parts still in circulation (mother boards, displays, power supplies) to provide the client with the best available technology. These repairs were completed to military standards and kept the RCT effective, allowing for the Sentinel radar to remain operational. However, the supply of outdated parts was eventually no longer available. Ensil offered the best possible solution, utilizing the skills of their knowledgeable engineering staff, they would reverse engineer a new computer to replace the obsolete RCT while maintaining the same form, fit and function.

Ensil

Reliability of Embedded Planar Capacitors under Temperature and Voltage Stress

Technical Library | 2015-05-21 18:46:31.0

In this work the reliability of an embedded planar capacitor laminate under temperature and voltage stress is investigated. The capacitor laminate consisted of an epoxy-BaTiO3 composite sandwiched between two layers of copper. The test vehicle with the embedded capacitors was subjected to a temperature of 125oC and a voltage bias of 200 V for 1000 hours. Capacitance, dissipation factor, and insulation resistance were monitored in-situ. Failed capacitors exhibited a sharp drop in insulation resistance, indicating avalanche breakdown. The decrease in the capacitance after 1000 hours was no more than 8% for any of the devices monitored. The decrease in the capacitance was attributed to delamination in the embedded capacitor laminate and an increase in the spacing between the copper layers.

CALCE Center for Advanced Life Cycle Engineering

Automated Fluid Dispensing for Epoxy

Technical Library | 2015-06-30 16:07:12.0

Robotics for automated fluid dispensing have the ability to apply a variety of materials including epoxy, silicone, and acrylic coatings. These materials are extensively used in today’s high-speed fluid dispensers for the electronics industry. Whether a dispenser is applying epoxy or another material, the central concept for applying any form of material remains the same. Specific points of an item being dispensed onto are programmed into the dispensing system. The automated fluid dispensers software interprets the programmed information and keeps the travel path in memory. A robotic arm moves fluid dispensing nozzles along this travel path and applies epoxy onto the surface of the item with precise accuracy. Machine speed can be adjusted to emit varying amounts of epoxy. The overall application process is auto-regulating and will not be disrupted.

ETS - Energy Technology Systems, Inc.

Printed Circuit Board For Industrial Application Drives a wave of Innovation

Technical Library | 2016-08-02 06:04:42.0

The next generation FUNDAS rest on one and only one motto (i.e.) technology up-gradation. For innovations in any corner of the world, a completely unique electronic solution is derived that accounts for fast trending modernization in the lifestyle of humans. With electronic design or manufacturing solution, the printed circuit boards are the groundwork for every electronic project. As the electronic control system and instruments are now applied in every predominant market across the globe, the use of PCB is predicted to have universal application in the global society. This article details you on the type of PCB’s used in the industrial sector, the application of PCB and innovations marked in the industrial sector with current steps taken by PCB manufacturers to provide unique solutions to the industrial sharks. See more: http://www.technotronix.us/pcbblog/printed-circuit-board-for-industrial-application-drives-a-wave-of-innovation/

Technotronix


any searches for Companies, Equipment, Machines, Suppliers & Information

SMTAI 2024 - SMTA International

High Precision Fluid Dispensers
Potting and Encapsulation Dispensing

High Throughput Reflow Oven
PCB Handling Machine with CE

World's Best Reflow Oven Customizable for Unique Applications
Solder Paste Dispensing

High Resolution Fast Speed Industrial Cameras.
Fully Automatic BGA Rework Station

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...