Technical Library | 2023-01-17 17:50:59.0
Heller's new Condenser Tube Flux Recovery System is designed to provide more efficient flux collection than earlier Heller flux collection systems; while providing minimal down time for inspection and cleaning. The entire system easily fits within the rear of the top shell of an 1800-EXL oven. The system utilizes a different set of top shell caps specially designed to provide the best serviceability of both the flux collection system and maintenance of the heater zone blower motors.
Technical Library | 2023-09-18 03:40:02.0
Our SMT intelligent solder paste supply system is the perfect solution for businesses that need to improve the accuracy and consistency of their SMT paste printing. Our system uses the latest technology to automatically dispense the correct amount of solder paste to each stencil opening, ensuring that your SMT assemblies are consistently high-quality.
Technical Library | 2019-07-01 10:44:11.0
In the electronics industry of today, companies emphasize better quality, lower cost, and shorter lead time on their products in order to keep up with their competitors. ACI Technologies (ACI) has been utilizing Computer Aided Design (CAD), Computer Aided Manufacturing(CAM), and Computer Aided Engineering (CAE) in its development of advanced electronics systems. CAD utilizes computer systems to assist in the creation, modification, analysis, and optimization of a design [1].
Technical Library | 2013-11-14 10:43:40.0
Understanding accuracy and repeatability is an important step to analyze fluid dispensing system performance. They can also be prone to misinterpretation when reviewing a product specification. A dispensing motion system can be made to perform better or worse under different operating conditions. This article will explain accuracy and repeatability, and how they can be applied to different specifications. It will also discuss key considerations when interpreting accuracy and repeatability for decision making.
Technical Library | 2021-12-31 06:09:47.0
The packaging method of surface mount components has become an important part of the SMT system. It directly affects the efficiency of assembly production and must be optimized in combination with the type and number of feeders of the SMT machine. There are four main types of packaging for surface mount components, Tape, tube, tray and bulk.
Technical Library | 2009-03-05 15:46:54.0
In a recent survey of 89 organizations conducted by Whataboutquality.com, respondents were asked what few key characteristics defined quality, in the eyes of their customer, the most popular response was: the product or service met my requirements. The next two most popular responses were: it worked like I expected and it was a good value, worth what I paid for it (...) So how do you continue to exceed customer expectations and simultaneously reduce costs? There are two paths to take. You can find and reduce the variation in your process and you can eliminate as much of the non-value-added waste in your operation.
Technical Library | 1999-05-09 13:07:16.0
This paper will give the reader a general understanding of EOS and ESD phenomena. It specifically addresses hand soldering's role in EOS and ESD and how to protect against and test for potential problems. It discusses how Metcal Systems address EOS and ESD concerns and how they differ from conventional soldering systems.
Technical Library | 2013-07-02 16:44:31.0
AOI and AXI systems can address multiple tasks in various locations of the manufacturing process and have become the leading technologies in the quest to identify defects and improve process yields.
Technical Library | 2021-11-26 01:18:30.0
The components of industrial control system (ICS) can be roughly divided into two categories according to their location: control center equipment and remote site equipment.
Technical Library | 2017-12-21 11:24:05.0
The present work concerns on the use of sensors to monitor the structural health of wind turbine . Conventionally the inspection was made using non-contact sensing during the turbine’s inoperable period hence loss occurred. A real -time monitoring system via embedded wireless sensor is preferred but the sensor could only be implanted using non-contact printing method due to most turbine blade s’ curved surface. Conductive ink associate d with non-contact printing method via fluid dispensing system are proposed since conductive inks are proven stretchable and fluid dispensing system enables printing on various substrates and works well with any materials...
Electronic manufacturing services - electronic design, development and manufacturing. Circuit board design, prototyping, FPGA services, signal integrity and simulation, pcb assembly. Factories in California USA and Malaysia.
Manufacturer / Consultant / Service Provider
3240 Scott Blvd
Santa Clara, CA USA
Phone: +1 408 980 0400
