Technical Library | 2015-06-22 16:39:47.0
Surface finishing is an integral part of any PCB fabrication. It is generally applied to exposed Cu connectors and conductors on the board. Surface finishing has numerous important functions. It serves as a protective layer for the Cu connectors during storage. The surface finish helps minimize or reduce tarnish of the Cu substrate. Additionally, since it is the layer that comes into contact with other components during assembly, it ensures good solderability between the PCB and the component during assembly. Furthermore after assembly, the finish helps prolong the integrity of the solder joint during use. A general review of common PCB surface finishes is presented. The advantages and disadvantages of each are discussed and compared.
Technical Library | 2016-11-30 15:53:15.0
The use of microvias in Printed Circuit Boards (PCBs) for military hardware is increasing as technology drives us toward smaller pitches and denser circuitry. Along with the changes in technology, the industry has changed and captive manufacturing lines are few and far between. As PCBs get more complicated, the testing we perform to verify the material was manufactured to our requirements before they are used in an assembly needs to be reviewed to ensure that it is sufficient for the technology and meets industry needs to better screen for long-term reliability. The Interconnect Stress Testing (IST) protocol currently used to identify manufacturing issues in plated through holes, blind, or buried vias are not necessarily sufficient to identify problems with microvias. There is a need to review the current IST protocol to determine if it is adequate for finding bad microvias or if there is a more reliable test that will screen out manufacturing inconsistencies. The objective of this research is to analyze a large population of PCB IST coupons to determine if there is a more effective IST test to find less reliable microvias in electrically passing PCB product and to screen for manufacturing deficiencies. The proposed IST test procedure will be supported with visual inspection of corresponding microvia cross sections and Printed Wiring Assembly (PWA) acceptance test results. The proposed screening will be shown to only slightly affect PCB yield while showing a large benefit to screening before PCBs are used in an assembly.
Technical Library | 2012-05-03 20:40:10.0
First published in the 2012 IPC APEX EXPO technical conference proceedings. Increased pressures to reduce time to market and time to volume have forced many manufacturers of populated printed circuit boards to rely on capacitively coupled, un-powered, vec
Technical Library | 2018-03-13 14:12:34.0
Many companies take their supply chain for granted until they need an obsolete part or a hard-to-find component. Then the importance of having resourceful contract manufacturing partners becomes an incredibly valuable asset.
Technical Library | 2018-07-11 22:46:13.0
For a demanding automotive electronics assembly, a highly thermal fatigue resistant solder alloy is required, which makes the lead-free Sn-Ag-Cu type solder alloy unusable. Sn-Ag-Bi-In solder alloy is considered as a high reliability solder alloy due to significant improvement in thermal fatigue resistance as compared to a standard Sn-Ag-Cu alloy. The alloy has not only good thermal fatigue properties but it also has superior ductility and tensile strength by appropriate addition of In; however, initial results indicated a sub-par performance in joint reliability when it is soldered on a printed circuit board (PCB) with Electroless Nickel Immersion Gold (ENIG) surface finish. Numerous experiments were performed to find out appropriate alloying element which would help improve the performance on ENIG PCBs. Sn-Ag-Bi-In solder alloys with and without Cu additions were prepared and then tests were carried out to see the performance in a thermal fatigue test and a drop resistance test.to investigate the impact of Cu addition towards the improvement of joint reliability on ENIG finish PCB. Also, the mechanism of such improvement is documented.
Technical Library | 2013-09-22 02:52:56.0
The PCB-assembly industry in constantly changing. Smaller footprints, new types of components and larger and more complex designs are accompanied by constant competitive pressures. As a result, electronics manufacturers need to continuously adapt their processes and make sure they exploit every opportunity for efficiency gains. This is the only way to improve quality and time to market and to increase profitability.
Technical Library | 2015-09-17 17:36:56.0
RoHS legislated restrictions on the materials used in electronics manufacture have imparted significant challenges on the electronics industry since their introduction in 2006. The greatest impacts have been felt by the mandated elimination of lead from electronic solder followed by the demand for the elimination of haloids from flame retardants used in traditional PCB laminates. In the years which have followed the electronics industry has been beset with a host of new challenges in its effort to comply. Failure mechanisms, both new and old, have surfaced which demand solution and the industry suppliers and manufacturing technologists have worked diligently to remedy those vexing faults through the development of a wide range of new materials and equipment for both board manufacture and assembly, along with modifications to the processes used in the manufacture and assembly of printed circuit boards.
Technical Library | 2008-05-07 17:54:58.0
Tracking goods through manufacturing was originally accomplished with pencil, paper and human input. Barcodes introduced an automated, machine-readable tracking mechanism that streamlined all types of manufacturing. But modern printed circuit board (PCB) assemblies are running into limitations because of barcode labels. And though barcodes and RFID tags will co-exist, the relatively large barcode labels have to find increasingly scarce real estate on high density boards.
Technical Library | 2017-06-23 12:42:59.0
End-to-end PCB assembly by world-class companies like Power Design Services allows you to focus on your core competencies with the added benefits of reduced cost and time to market. From material procurement to circuit board design and manufacturing, and supply chain management, we serve your needs helping you reach customers faster. Here is an overview of what our turnkey electronic manufacturing services consist of, and how you can use them to reduce your build time and cost.
Technical Library | 2021-08-04 18:36:17.0
In this paper, the existing status of PCB manufacturing environment and future development towards smart manufacturing system (SMS) are discussed. A cloud manufacturing system (CMS) paradigm is introduced in the existing PCB manufacturing environment to get easy access to resources, materials, manufacturing processes, planning problems and data sharing networks. The goal is to integrate the information sharing from planning problems, PCB assembly lines, retailer and shipment department to CMS for smart planning decisions to cope with the increasing demand and profit enhancement strategies. A conceptual framework is presented to introduce the smart manufacturing environment in the traditional PCB manufacturing system. The suggested framework of SMS helps to improve the performance of PCB manufacturing industries regarding smart planning and scheduling, intelligent monitoring of smart assembly lines for efficiency and production enhancement.
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
