Technical Library | 2017-03-30 18:34:52.0
There are multiple methods, each with its associated benefits for given applications, for printing either solder paste or paste flux for BGA rework. Each of these methods is best-suited for a given situation, board layout and skill level of operators performing the BGA rework. This discussion will layout the various methods and present the specific circumstances for which the specific technique is most wellsuited. In addition, the pluses and minuses for each of the approaches will be discussed in detail.
Technical Library | 2007-01-31 15:17:04.0
The goal of this project is to evaluate the reliability of lead-free BGA solder joints with a variety of different pad sizes using several different BGA rework methods. These methods included BGAs reworked with both flux only and solder paste attachment techniques and with or without the use of the BEST stay in place StencilQuick™. The daisy chained test boards were placed into a thermal test chamber and cycled between -25ºC to 125ºC over a 30 minute cycle with a 30 minute dwell on each end of the cycle. Each BGA on the board was wired and the continuity assessed during the 1000 cycles the test samples were in the chamber.
Technical Library | 2007-02-01 09:57:15.0
The rapid assimilation of Ball Grid Array (BGA) and other Area Array Package technology in the electronics industry is due to the fact that this package type allows for a greater I/O count in a smaller area while maintaining a pitch that allows for ease of manufacture.
Technical Library | 2007-01-31 14:14:56.0
This paper explains the solder paste reflow process and the best practices to follow when developing your profile.
Technical Library | 2014-03-27 14:50:01.0
Because of the phase out of CFC's and HCFC's, standard solder pastes and fluxes evolved from RA and RMA fluxes, to No-Clean, to low residue No-Clean, to very low residue No-Clean. Many companies came out with their cleaning solutions, aqueous and semi-aqueous, with each product release being more innovative than the previous one. Unfortunately for most of the suppliers of cleaners, two other trends appeared; lead-free soldering and the progressive miniaturization of electronic devices.
Technical Library | 2022-02-16 15:34:32.0
Because of the phase-out of CFCs and HCFCs, standard solder pastes and fluxes evolved from RA and RMA fluxes to No-Clean, to low residue No-Clean, to very low residue No-Clean. Many companies came out with their cleaning solutions, aqueous and semi-aqueous, with each product release being more innovative than the previous one. Unfortunately for most of the suppliers of cleaners, two other trends appeared; lead-free soldering and the progressive miniaturization of electronic devices
Technical Library | 2021-07-06 21:13:36.0
The surface finishes commonly used on printed circuit boards (PCBs) have an effect on solder paste performance in the surface mount process. Some surface finishes are non-planar like hot air solder level (HASL) which can lead to inconsistencies in solder paste printing. Other surface finishes are difficult to wet during reflow like organic solderability preservative (OSP). What is the overall effect of surface finish on solder paste performance? Which solder paste is best for each surface finish? It is the goal of this paper to answer these questions.
Technical Library | 2010-03-18 14:02:03.0
Selecting products that have been qualified by industry standards for use in printed circuit board assembly processes is an accepted best practice. That products which have been qualified, when used in combinations not specifically qualified, may have resultant properties detrimental to assembly function though, is often not adequately understood. Printed circuit boards, solder masks, soldering materials (flux, paste, cored wire, rework flux, paste flux, etc.), adhesives, and inks, when qualified per industry standards, are qualified using very specific test methods which may not adequately mimic the assembly process ultimately used.
Technical Library | 2007-09-13 16:58:52.0
With the use of laser light for reflow having been established, all that remains is to apply it to best effect. Each time a laser is fired, it pumps a specific amount of energy at a particular wavelength to a particular point in space. Where technique comes in is choosing where and for how long to apply that light along with the application of accessory equipment to optimize solder paste reflow. This presentation covers the specifics of how to determine which process choices are the right process choices based on the needs of your product to maximize yield and throughput.
Technical Library | 2021-11-16 22:17:27.0
Ultrasonics, coupled with an aqueous detergent process that cleans at below 43ºC, may be best suited for fine-pitch SMT screens and stencils. Aqueous detergents clean more effectively than solvents, with little or no environmental impact. Because of the environmental concerns driving today's technology decisions, the once simple decision of selecting a stencil cleaning process is now clouded with different chemicals, different cleaning machines and various types of solder paste, all with specific environmental, health and safety related issues and regulations.