Technical Library | 2019-06-21 10:39:15.0
Recently, an ACI Technologies (ACI) customer called to discuss failures that they had observed with some through-hole capacitor parts. The components were experiencing failures following vibration and accelerated stress testing. Upon receipt of the samples, ACI performed three levels of inspection and Energy Dispersive Spectroscopy (EDS) testing to investigate the root cause of the failures. These analyses enabled ACI to verify the elements comprising the solder joints and make the following recommendations in order to prevent future occurrences. The first inspection was to investigate the capacitor leads using optical microscopy, and no anomalies were found that could indicate bad parts from the vendor or improper handling prior to assembly. However, vertical fill in the barrel of the plated through-holes was too close to the IPC-A-610 minimum specification of 75% to determine a pass/fail condition, and therefore required further investigation.
Technical Library | 2020-04-14 15:56:32.0
This paper will focus on the application requirements of solder printing small aperture designs, concentrating on 008004 (inch) / 0201 (metric) size components, and the results of a design of experiment printing these challenging apertures. As Moore's law continues to be applied to component miniaturization, the next installment of reduced packaging has arrived in the form of the 008004/0201 for resistors and capacitors. Component size roughly the size of a grain of sand presents specific challenges to the solder printing process. To address these challenges, each aspect of the printing process will need be examined. This includes essential machine requirements, including correct squeegee blades, tooling support, and calibrations, to meet the demanding specifications. The correct match and design of materials will be addressed, focusing on the stencil and substrate design along with solder paste and cleaning solvent requirements. A design of experiment will be reviewed that applies the machine and materials discussed, including the printer and Solder Paste Inspection (SPI) setup and the specific machine parameters used. The results of these DOE's will then be closely examined.
Technical Library | 2022-04-29 00:49:12.0
Tools: soldering iron, soldering iron stand, wet sponge, tweezers, rosin, solder, absorbent cotton, 95% alcohol, chip resistors, capacitors, circuit boards, 220V power supply..... http://www.leadersmt.com/gen2/1028113523/?mod=file&col_key=download
Technical Library | 2022-04-28 06:42:19.0
I. Chip capacitors(MLCC) The full name of chip capacitors: multilayer (multilayer, laminated) chip ceramic capacitors, also known as chip capacitors, chip capacitance.
Technical Library | 2022-04-26 03:27:56.0
The naming of the chip capacitor: The parameters included in the name of the chip capacitor include the size of the chip capacitor, the material used for this chip capacitor, the required accuracy, the required voltage, the required capacity, the requirements of the terminal and packaging requirements. Generally, the parameters to be provided for ordering a chip capacitor should be the size, the required accuracy, the voltage requirement, the capacity value, and the required brand.
Technical Library | 2011-04-14 15:29:39.0
Multilayer Ceramic Capacitors (MLCC) come in a broad range of sizes, geometries, and values, offering design engineers with many options for designing circuits. In many cases these MLCC’s offer advantages over other types of capacitors including low ESR/E
Technical Library | 2022-04-27 01:34:43.0
SMD capacitors and resistors have small sizes and many models. Some manufacturers buy a lot of products and do not use them up in time. The problem of storage is always a headache. So how should chip capacitors and resistors be stored? There are also precautions when using chip capacitors. Please see the following information and hope it will help you.
Technical Library | 2015-01-22 17:32:27.0
Temperature requirements for ceramic capacitors have increased significantly with recent advances in deep-well drilling technology. Increasing demand for oil and natural gas has driven the technology to deeper and deeper deposits resulting in extreme temperature environments up to 200°C and above. A novel capacitor solution utilizing temperature-stable base-metal electrode capacitors in a molded and leaded package addresses the growing market high temperature demands of (1) capacitance stability, (2) long service life, and (3) mechanical durability. A range of high temperature C0G capacitors capable of meeting this 200°C and above high temperature environment has been developed. This paper will review the electrical, reliability, and mechanical performance of this new capacitor solution
Technical Library | 2015-05-21 18:46:31.0
In this work the reliability of an embedded planar capacitor laminate under temperature and voltage stress is investigated. The capacitor laminate consisted of an epoxy-BaTiO3 composite sandwiched between two layers of copper. The test vehicle with the embedded capacitors was subjected to a temperature of 125oC and a voltage bias of 200 V for 1000 hours. Capacitance, dissipation factor, and insulation resistance were monitored in-situ. Failed capacitors exhibited a sharp drop in insulation resistance, indicating avalanche breakdown. The decrease in the capacitance after 1000 hours was no more than 8% for any of the devices monitored. The decrease in the capacitance was attributed to delamination in the embedded capacitor laminate and an increase in the spacing between the copper layers.
Technical Library | 1999-05-06 12:08:08.0
Input voltage capacitors are typically the parts that fail first in a high power circuit. Today's requirements for increasingly smaller packages is driving high component densities in power systems, as in all systems. As the package size...
