Technical Library: century technology

Thermal Interface Material (TIM) Dispensing For Consumer Products

Technical Library | 2023-08-16 18:25:16.0

In one of our Consumer Electronics projects, a leader of networking technologies requested to test dispensing performance of a thermally conductive material, Fujipoly Sarcon SPG-50A. This material improves heat dissipation for higher frequency applications and reduces the negative effects of thermal resistance under heat, cold, humid, and thermal shock conditions. The customer's goal was to dispense a 1mm diameter dot with acceptable speed and consistency.

GPD Global

Small Volume Solder Paste Dispensing for Aerospace and Defense

Technical Library | 2023-09-07 14:38:31.0

A repeat customer specializing in high-technology interconnect, sensor, and antenna solutions, partnered with us to dispense small volumes of solder paste (Indium 10.1 SAC305 T6SG 78%m) onto backplane connectors – gold pads 0.175mm x 0.225mm. We performed a test requiring 0.200mm diameter or smaller dots to demonstrate the dispensing capability required.

GPD Global

BGA Rework. A Comparative Study of Selective Solder Paste Deposition For Area Array Packages

Technical Library | 2007-02-01 09:57:15.0

The rapid assimilation of Ball Grid Array (BGA) and other Area Array Package technology in the electronics industry is due to the fact that this package type allows for a greater I/O count in a smaller area while maintaining a pitch that allows for ease of manufacture.

BEST Inc.

Laser Solder Reflow: A Process Solution Part I

Technical Library | 2007-09-06 11:03:33.0

EFD Inc. and Leister USA have collaborated to bust the myth that you cannot perform laser reflow with solder paste. Using Leister diode lasers, EFD has formulated solder pastes that survive the rapid reflow cycle typical of laser heating. These solder pastes reflow and wet well, without spatter, even when heating is accomplished in less than half a second. The flux core in wire solders cannot boast such flux spatter resistance in such an aggressive heating environment.

Nordson EFD

Printable Nanocomposites for Electronic Packaging

Technical Library | 2008-06-25 16:11:51.0

Printing technologies provide a simple solution to build electronic circuits on o low cost flexible substrates. Nanocomposites will play important role for developing advanced printable technology. Advanced printing is relatively new technology and need more characterization and optimization for practical applications. In the present paper, we examine the use of nanocomposites or materials in the area of printing technology.

i3 Electronics

Justifying AOI and Automated X-Ray

Technical Library | 2013-07-02 16:44:31.0

AOI and AXI systems can address multiple tasks in various locations of the manufacturing process and have become the leading technologies in the quest to identify defects and improve process yields.

Nordson YESTECH

Automotive Safety Systems Driving Growth in Automotive Sensor Cable Assemblies

Technical Library | 2015-01-12 09:27:49.0

V2V is a collision avoidance technology that transmits data between vehicles to help warn drivers of potential crashes. This technology would improve safety by allowing vehicles to communicate with each other and exchange basic safety data, such as position and speed and warn the driver of potentially dangerous situations.

Schleuniger, Inc.

The Proximity of Microvias to PTHs And Its Impact On The Reliability

Technical Library | 2007-05-09 18:26:16.0

High Density Interconnect (HDI) technology is fast becoming the enabling technology for the next generation of small portable electronic communication devices. These methods employ many different dielectrics and via fabrication technologies. In this research, the effect of the proximity of microvias to Plated Through Holes (PTHs) and its effect on the reliability of the microvias was extensively evaluated. The reliability of microvia interconnect structures was evaluated using Liquid-To-Liquid Thermal Shock (LLTS) testing (-55oC to +125oC). Comprehensive failure analysis was performed on microvias fabricated using different via fabrication technologies.

Universal Instruments Corporation

Enhancing Mechanical Shock Performance Using Edgebond Technology

Technical Library | 2014-06-26 16:43:12.0

Edgebond adhesives have been widely used by the industry for improving the shock performance of area array packages. Most of the studies focus on the impact of material properties, such as coefficient of thermal expansion (CTE) and glass transition temperature (Tg), on reliability at room temperature. However, the operating temperature of a component on the printed circuit board bonded with edgebond adhesive can be close to or exceed Tg of the adhesive, where the material properties may be very different than at room temperature.

Cisco Systems, Inc.

3D Assembly Process a Look at Today and Tomorrow

Technical Library | 2016-04-21 14:10:55.0

The world of electronics continues to increase functional densities on products. One of the ways to increase density of a product is to utilize more of the 3 dimensional spaces available. Traditional printed circuit boards utilize the x/y plane and many miniaturization techniques apply to the x/y space savings, such as smaller components, finer pitches, and closer component to component distances.This paper will explore the evolution of 3D assembly techniques, starting from flexible circuit technology, cavity assembly, embedded technology, 3 dimensional surface mount assembly, etc.

Flex (Flextronics International)

  1 2 3 Next

century technology, inc searches for Companies, Equipment, Machines, Suppliers & Information

Precision PCB Services, Inc
Precision PCB Services, Inc

Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.

Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

1750 Mitchell Ave.
Oroville, CA USA

Phone: (888) 406-2830

2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven
consignment program

World's Best Reflow Oven Customizable for Unique Applications
SMT Machines

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
SMT feeders

High Precision Fluid Dispensers
design with ease with Win Source obselete parts and supplies

"回流焊炉"