Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2023-01-17 17:22:28.0
The impact of voiding on the solder joint integrity of ball grid arrays (BGAs)/chip scale packages (CSPs) can be a topic of lengthy and energetic discussion. Detailed industry investigations have shown that voids have little effect on solder joint integrity unless they fall into specific location/geometry configurations. These investigations have focused on thermal cycle testing at 0°C-100°C, which is typically used to evaluate commercial electronic products. This paper documents an investigation to determine the impact of voids in BGA and CSP components using thermal cycle testing (-55°C to +125°C) in accordance with the IPC- 9701 specification for tin/lead solder alloys. This temperature range is more typical of military and other high performance product use environments. A proposed BGA void requirement revision for the IPC-JSTD-001 specification will be extracted from the results analysis.
Technical Library | 2023-11-25 07:46:13.0
In the dynamic realm of Surface Mount Technology (SMT), where efficiency and precision are paramount, I.C.T, a renowned SMT equipment manufacturer, proudly unveils its latest innovation – the I.C.T-910 Automatic IC Programming System. Crafted to cater to the intricate demands of SMD chip programming, this cutting-edge device vows to redefine your programming experience and elevate production capabilities. Programming system.png The Power of IC Programming System: As a beacon of excellence in IC Programming Systems, the I.C.T-910 seamlessly integrates advanced technology with user-friendly features. This system empowers manufacturers in the SMT industry, offering versatility in programming needs by accommodating a wide range of SMD chips. Precision Programming: The I.C.T-910 boasts unparalleled precision in programming SMD chips, ensuring accuracy in every generated code. In the SMT industry, where even the slightest error can lead to setbacks, this precision is indispensable. Efficiency Redefined: Accelerate your production timelines with the I.C.T-910's efficient programming capabilities. Engineered to optimize workflows, this system ensures rapid programming without compromising quality, recognizing that time is money in the SMT industry. User-Friendly Interface: Navigating the complexities of IC programming is simplified with the I.C.T-910's intuitive user interface. Operators, even without extensive programming expertise, can harness the system's power, minimizing the learning curve and maximizing productivity. Compatibility and Adaptability: The I.C.T-910 breaks free from limitations, supporting a wide array of SMD chip models. It is a versatile solution for diverse programming requirements, allowing you to stay ahead of technological advancements. Why Choose I.C.T-910 IC Programming System? 8 sets of 32-64sit burners Nozzle: 4pcs Camera: 2pcs (Component camera + Marking camera) UPH: 2000-3000PCS/H Package type: PLCC, JLCC, SOIC, QFP, TQFP, PQFP, VQFP, TSOP, SOP, TSOPII, PSOP, TSSOP, SON, EBGA, FBGA, VFBGA, BGA, CSP, SCSP, and so on. Compatibility: Adapters provided based on customer products. Simple operation interface: Modular and layered interface with pictures and texts for easy operation. System upgrade: Free software upgrade service. Reliability: Trust in the I.C.T-910, a programming system that prioritizes reliability. Rigorous testing ensures consistent and dependable performance, reducing the risk of programming errors and downtime. Elevate Your Competitiveness: Incorporate the I.C.T-910 into your production line to elevate competitiveness in the market. Stay ahead with a programming system designed to meet the demands of the fast-paced SMT industry. Embrace the Future with I.C.T-910: In a landscape where precision, efficiency, and adaptability are non-negotiable, the I.C.T-910 Automatic IC Programming System emerges as the game-changer for SMT manufacturers. Revolutionize your programming processes, enhance productivity, and future-proof your operations with the I.C.T-910. Choose I.C.T-910 and stay ahead in the SMT industry, ushering in the next era of IC programming excellence.
Technical Library | 2020-07-02 13:29:37.0
Industry standards such as J-STD-005 and JIS Z 3284-1994 call for the use of viscosity measurement(s) as a quality assurance test method for solder paste. Almost all solder paste produced and sold use a viscosity range at a single shear rate as part of the pass-fail criteria for shipment and customer acceptance respectively. As had been reported many times, an estimated 80% of the defects associated with the surface mount technology process involve defects created during the printing process. Viscosity at a single shear rate could predict a fatal flaw in the printability of a solder paste sample. However, false positive single shear rate viscosity readings are not unknown.
Technical Library | 2015-08-13 15:52:40.0
Pad cratering has become more prevalent with the switch to lead free solders and lead free compatible laminates. This mainly is due to the use of higher reflow temperature, stiffer Pb-free solder alloys, and the more brittle Pb-free compatible laminates. However, pad cratering is difficult to detect by monitoring electric resistance since pad cratering initiates before an electrical failure occurs. Several methods have been developed to evaluate laminate materials' resistance to pad cratering. Pad-solder level tests include ball shear, ball pull and pin pull. The detailed methods for ball shear, ball pull, and pin pull testing are documented in an industry standard IPC-9708. Bansal, et al. proposed to use acoustic emission (AE) sensors to detect pad cratering during four-point bend test. Currently there is an industry-working group working on test guidelines for acoustic emission measurement during mechanical testing.
Technical Library | 2000-11-13 20:45:03.0
Free 16 page guide quickly explains how to read Dummy Component and test vehicle part numbers. Covers CSP, BGA, QFP, SOIC, Flip Chips, flat packs and discretes and chips.
Technical Library | 2020-12-24 02:50:56.0
A method for packaging integrated circuit silicon die in thin flexible circuits has been investigated that enables circuits to be subsequently integrated within textile yarns. This paper presents an investigation into the required materials and component dimensions in order to maximize the reliability of the packaging method. Two die sizes of 3.5 mm×8 mm× 0.53 mm and 2 mm×2 mm×0.1 mm have been simulated and evaluated experimentally under shear load and during bending. The shear and bending experimental results show good agreement with the simulation results and verify the simulated optimal thickness of the adhesive layer. Three underfill adhesives (EP30AO, EP37-3FLF, and Epo-Tek 301 2fl), three highly flexible adhesives (Loctite 4860, Loctite 480, and Loctite 4902), and three substrates (Kapton,Mylar, and PEEK) have been evaluated, and the optimal thickness of each is found. The Kapton substrate, together with the EP37-3FLF adhesive, was identified as the best materials combination with the optimum underfill and substrate thickness identified as 0.05 mm.
Technical Library | 2020-11-29 22:06:45.0
Plastic laminates are increasingly used as interposers within chip packaging applications. As a component within the package, the laminate is subjected to package moisture sensitivity testing. The moisture requirements of chip packaging laminates are related to ambient moisture absorption and thermal cycling. Printed wiring board (PWB) laminates, however, are gauged on properties relating to wet processes such as resist developing, copper etching, and pumice scrubbing. Consequently, printed wiring board moisture absorption test methods differ from chip packaging test conditions.
Technical Library | 2010-03-30 21:51:23.0
This paper presents the drop test reliability results for edge-bonded 0.5mm pitch lead-free chip scale packages (CSPs) on a standard JEDEC drop reliability test board.
Technical Library | 2010-09-02 13:13:03.0
As chip packaging and interconnectivity have become more dense and operate at higher clock frequencies, physical access for traditional bed-of-nails testing becomes limited. This results in loss of ICT (in-circuit test) fault coverage and higher test fi
