Technical Library: circuits board (Page 13 of 31)

Conformal Coating Thickness Measurement

Technical Library | 2013-10-13 10:54:13.0

The measurement of the conformal coating thickness on a printed circuit board (PCB) to ensure internal and international standards are met is now a critical factor in conformal coating process control. There are several methods for measurement of conformal coating thickness and they fall into two categories. These categories are wet film measurements applied during coating application and dry film measurements made after the coating is dried enough not to damage the coating.

SCH Technologies

Selective protection for PCBs

Technical Library | 2020-02-18 09:56:24.0

Glob Top, Dam and Fill & Flit Chip Underfill To protect PCBs from damaging outside influences, they are coated with a thin layer of casting resin or protective finish during the conformal coating process. In addition to sealing the entire circuit board, it is possible to pot only sections or individual components on the substrate. Different methods ranging from "glob top" to "dam and fill" and "flip chip underfill" have been developed for this purpose.

Scheugenpflug Inc.

Conformal Coating Defects

Technical Library | 2023-07-04 17:31:22.0

Conformal Coatings are polymeric materials used to protect circuitry, parts, and related components. They are most commonly used to protect printed circuit boards (PCBs) and electronic devices. However, conformal coatings can be applied to a wide variety of materials, including metal, plastic, silicone, ceramics, glass, and even paper. We use the term "substrate" to refer to an object or material that's been coated with a conformal coating.

Diamond MT

Introducing the OSP Process as an Alternative to HASL

Technical Library | 1999-08-09 11:09:42.0

Organic Solderability Preservatives (OSPs), also known as anti-tarnish, on bare copper printed circuit boards (PCBs) are becoming more prevalent in the electronics industry as the low-cost replacement to Hot Air Solder Leveling (HASL). Introducing the anti-tarnish alternative into the customer sites requires working closely with the coating supplier, assembler, and Original Equipment Manufacturer (OEM) to gain a mutual understanding of respective processing concerns and finished product requirements.

Viasystems Group, Inc.

Design For Test Considerations For PCB Design

Technical Library | 2006-07-14 11:48:11.0

The perennial question in electronics design and manufacture is: "How do I design a printed circuit board (PCB) so that it can be properly tested?" To achieve this objective, there are a number of design-for-test (DFT) considerations and techniques. Some are major, others, minor. However, the total contributes to a highly effective PCB design so that testing procedures applied to a given design result in high 90 percent plus test coverage.

NexLogic Tech, Inc.

Assembly And Reliability Issues Associated With Leadless Chip Scale Packages

Technical Library | 2006-10-02 14:26:47.0

This paper addresses the assembly and reliability of 0.5 mm pitch leadless Chip Scale Packages (CSP) on .062" immersion Ag plated printed circuit boards (PCB) using Pb-free solder paste. Four different leadless CSP designs were studied and each was evaluated using multiple PCB attachment pad designs.

Universal Instruments Corporation

Process Development And Characterization Of The Stencil Printing Process For Small Apertures

Technical Library | 2008-01-16 18:25:55.0

The consumer's interest for smaller, lighter and higher performance electronics products has increased the use of ultra fine pitch packages, such as Flip Chips and Chip Scale Packages, in printed circuit board (PCB) assembly. The assembly processes for these ultra fine pitch packages are extremely complex and each step in the assembly process influences the assembly yield and reliability.

Speedline Technologies, Inc.

Fundamentals of Solder Paste Technology

Technical Library | 2008-03-03 19:43:53.0

Solder pastes are key materials in surface mount technology (SMT) for assembly of printed circuit boards (PCBs). Introduction of lead-free has placed new demands on materials and processes in SMT, requiring materials and process engineers to adopt to lead free whilst ensuring process yields stay at the highest possible levels. Key is the solder paste, a material of great complexity involving engineering sciences, metallurgy, chemistry and physics. This article helps those working with solder pastes improve their understanding of this key material.

BizEsp Ltd.

Meeting Heat And CTE Challenges Of PCBs And ICs

Technical Library | 2008-11-13 00:06:32.0

The electronics industry is facing issues with hot spots, solder joint stresses and Coefficient of Thermal Expansion (CTE) mismatch between PCB and IC substrate. Flip chip type packages for example have very low CTE compared to traditional PCB material. Thus it is necessary to have low CTE printed circuit boards in order to keep solder joint intact with such low CTE packages. There are currently several materials available in the market to address thermal and CTE challenges but each material has its own advantages and limitations...

Stablcor

Hybrid Drying Technology for In-line Aqueous Cleaning of Lead-Free Assemblies

Technical Library | 2009-01-21 23:16:14.0

This paper describes a new approach to drying circuit board assemblies that significantly reduces the cost of ownership of an aqueous cleaning system. Drying performance is increased through a hybrid drying process that reduces energy input, exhaust requirements and sound levels. The combination of high temperature blow-off and convection brings the flexibility to tailor drying performance to fit the product's drying requirements.

Speedline Technologies, Inc.


circuits board searches for Companies, Equipment, Machines, Suppliers & Information

SMTAI 2024 - SMTA International

High Precision Fluid Dispensers
One stop service for all SMT and PCB needs

High Throughput Reflow Oven
PCB Handling Machine with CE

World's Best Reflow Oven Customizable for Unique Applications