Technical Library | 2013-05-10 18:12:15.0
In today’s manufacturing environments, optimizing manufacturing costs and, especially Test and Inspection costs are high on most company’s agendas. Resources are tight and many employees have multiple roles to fulfill across the whole manufacturing line so, time is limited. Test suppliers need to provide a suite of tools to ensure the highest level of quality for customer shipments.
Technical Library | 1999-05-06 14:44:11.0
Semiconductor device manufacturers face many difficult challenges as we enter the 21st century. Some are direct consequences of adherence to Gordon Moore's Law, which states that device complexity doubles about every 18 months. Feature size reduction, increased wafer diameter, increased chip size, ultra-clean processing, and defect reduction among others are manifestations that have a direct bearing on the cost and quality of products, factory flexibility in responding to changing technology or business conditions, and on the timelines of product delivery to the ultimate customer.
Technical Library | 1999-08-09 11:09:42.0
Organic Solderability Preservatives (OSPs), also known as anti-tarnish, on bare copper printed circuit boards (PCBs) are becoming more prevalent in the electronics industry as the low-cost replacement to Hot Air Solder Leveling (HASL). Introducing the anti-tarnish alternative into the customer sites requires working closely with the coating supplier, assembler, and Original Equipment Manufacturer (OEM) to gain a mutual understanding of respective processing concerns and finished product requirements.
Technical Library | 2001-05-03 11:23:09.0
In this age of global competition, world class electronics manufacturers understand that increasing profit margins is accomplished not by increasing price or lowering the quality of components and workmanship, but by increasing production yields. Post-solder inspection ensures that your customers receive good product, but by separating the good boards from the bad boards you only measure yield, not improve it. A yield (and profit) improvement strategy consists of making measurements at critical stages, as early as possible in the assembly process, and adjusting the process parameters to achieve optimal performance.
Technical Library | 2006-11-01 22:37:23.0
Flip Chip Plastic Ball Grid Array (FCPBGA) modules, when subjected to extreme environmental stress testing, may often reveal mechanical and electrical failure mechanisms which may not project to the field application environment. One such test can be the Deep Thermal Cycle (DTC) environmental stress which cycles from -55°C to 125°C. This “hammer” test provides the customer with a level of security for robustness, but does not typically represent conditions which a module is likely to experience during normal handling and operation.
Technical Library | 2007-11-15 15:54:44.0
At the contractor level once a product is required to be soldered with lead-free solders all the processes must be assessed as to insure the same quality a customer has been accustomed to with a Sn63Pb37 process is achieved. The reflow, wave soldering and hand assembly processes must all be optimized carefully to insure good joint formation as per the appropriate class of electronics with new solder alloys and often new fluxes.
Technical Library | 2013-03-28 16:18:22.0
For the last couple of years, the main concerns regarding the electrical performance of blank PCB boards were impedance and ohmic resistance. Just recently, the need to reduce insertion loss came up in discussions with blank board customers (...) The paper describes the test vehicle and the testing methodology and discusses in detail the electrical performance characteristics. The influence of the independent variables on the performance characteristics is presented. Finally the thermal reliability of the boards built applying different copper foils and oxide replacements was investigated.
Technical Library | 2014-10-16 16:39:12.0
Key points are: *Long-term storage of BGA & QFP products may be required due to: Fab and assembly factory transfers Product obsolescence requiring customers make lifetime/EOL purchases Providing extended service (10+ years) on vehicles Other program needs * Integrity of EOL products in terms of solderability needs to be verified.
Technical Library | 2017-06-23 12:42:59.0
End-to-end PCB assembly by world-class companies like Power Design Services allows you to focus on your core competencies with the added benefits of reduced cost and time to market. From material procurement to circuit board design and manufacturing, and supply chain management, we serve your needs helping you reach customers faster. Here is an overview of what our turnkey electronic manufacturing services consist of, and how you can use them to reduce your build time and cost.
Technical Library | 2018-02-01 00:31:48.0
This paper briefly summarizes the technologies underpinning the evolution in electrical system diagnosis and repair, which include schematic layout automation using prototypes and rule-based styling, instant language translation, 2D/3D view links with schematics, interactive diagnostic procedures, and dynamically-generated signal-tracing diagrams. These technologies empower after-sales service teams with state-of-the-art capabilities, which not only reduce costs but also improve brand quality in the eyes of its customers.
winsouce.jpg)
.gif)
