Technical Library | 2007-09-06 11:03:33.0
EFD Inc. and Leister USA have collaborated to bust the myth that you cannot perform laser reflow with solder paste. Using Leister diode lasers, EFD has formulated solder pastes that survive the rapid reflow cycle typical of laser heating. These solder pastes reflow and wet well, without spatter, even when heating is accomplished in less than half a second. The flux core in wire solders cannot boast such flux spatter resistance in such an aggressive heating environment.
Technical Library | 2007-09-13 16:58:52.0
With the use of laser light for reflow having been established, all that remains is to apply it to best effect. Each time a laser is fired, it pumps a specific amount of energy at a particular wavelength to a particular point in space. Where technique comes in is choosing where and for how long to apply that light along with the application of accessory equipment to optimize solder paste reflow. This presentation covers the specifics of how to determine which process choices are the right process choices based on the needs of your product to maximize yield and throughput.
Technical Library | 2013-06-27 14:00:27.0
While IC level ESD design and the necessary protection levels are well understood, system ESD protection strategy and design efficiency have only been dealt with in an ad hoc manner. This is most obvious when we realize that a consolidated approach to system level ESD design between system manufacturers and chip suppliers has been rare. This White Paper discusses these issues in the open for the first time, and offers new and relevant insight for the development of efficient system level ESD design.
Technical Library | 2021-09-15 18:53:20.0
Many printed circuit board assemblies (PCBAs) have relays that are soldered to the PCB. If such an electromechanical component fails, it can cause the whole device to fail, just like any other electronic component. The spectrum of root causes that lead to an increased contact resistance or a complete contact failure is totally different from what usually occurs in the electronics domain. This article provides a detailed analysis of these failures and the corresponding root causes, many of them self-centering.
Technical Library | 2022-10-31 08:39:26.0
Minimum Order Quantity: 1/pcs Price: Negotiable,EXW Price Packaging Details: High quality carton packaging Delivery Time: 1-2 work days Payment Terms: L/C, D/A, D/P, T/T, Western Union, MoneyGram Supply Ability: 1000pcs monthly, delivery time 1-2 days
Technical Library | 2022-10-31 08:40:27.0
Minimum Order Quantity: 1/pcs Price: Negotiable,EXW Price Packaging Details: High quality carton packaging Delivery Time: 1-2 work days Payment Terms: L/C, D/A, D/P, T/T, Western Union, MoneyGram Supply Ability: 1000pcs monthly, delivery time 1-2 days
Technical Library | 2024-05-31 19:29:59.0
A-Laser enters the aerospace world with laser cutting services that continue to exceed performance expectations. The modern aerospace industry has strict tolerance requirements and A-Laser is prepared to meet those needs. For example, modern aerospace design dictates anywhere from dozens to millions of precise holes and channels. These must vary in thickness, diameters, and geometries. A-Laser is prepared to meet these requirements and we do so with faster, more versatile, more consistent and cost-effective tools.
Technical Library | 1999-08-05 10:52:56.0
This technology transfer was prepared by the Research Triangle Institute (RTI) as part of SEMATECH's Facility Fluids Project (S100). It is a compilation of information on existing facility fluids metric and test methods. Information on standard methods was gathered from SEMATECH and SEMI. Other information was obtained from a literature search of journals and conference proceedings. The published information primarily is concerned with the test equipment used and what levels of detection and purity were found. Many of the articles discussed the use of new equipment, either commercial or experimental. Extensive annotated bibliographies are append to the report.
Technical Library | 2015-11-12 19:04:51.0
In order to provide the functionality in today’s electronics, printed circuit boards are approaching the complexity of semiconductors. For flexible circuits with 1 mil lines and spaces, this means no nodules, no pits, and excellent ductility with thinner deposits. One of the areas that has to change to get to this plateau of technology is acid copper plating. Acid copper systems have changed in minor increments since their introduction decades ago. However, the basic cell design using soluble anodes in slabs or baskets has for the most part remained the same. Soluble, phosphorized, copper anodes introduce particulate and limits the ability to control plating distribution.
Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
