Technical Library | 2017-06-01 17:12:08.0
The corrosion of Nickel-Palladium-Gold (Ni-Pd-Au) finish terminals in humid environments is known to be reduced with the application of a conformal coating such as acrylic. Corrosion has a higher rate of occurrence around the terminal ‘knee’ of a surface mount component, which may be reduced with the application of conformal coatings. Although radio frequency (RF) plasma processing is generally known to enhance conformity of conformal coating to surfaces through ionic bombardment, the effect on the functionality of assembled printed circuit boards (PCB) is not as well known. The purpose of this study is to assess whether RF plasma processing can enhance the adhesive and coverage qualities of an acrylic conformal coating on PCBs, specifically on Ni-Pd-Au terminals with a knee, and if plasma processing has an effect on the electrical functionality of components and fully assembled PCB.
Technical Library | 2017-09-14 01:21:52.0
The electronics industry is experiencing a renaissance in semiconductor package technology. A growing number of innovative 3D package assembly methodologies have evolved to enable the electronics industry to maximize their products functionality. By integrating multiple die elements within a single package outline, product boards can be made significantly smaller than their forerunners and the shorter interconnect resulting from this effort has contributed to improving both electrical performance and functional capability. (...) This paper outlines both positive and negative aspects of current 3D package innovations and addresses the challenges facing adopters of silicon and glass based interposer fabrication. The material presented will also reference 3D packaging standards and recognize innovative technologies from a number of industry sources, roadmaps and market forecasts.
Technical Library | 2017-11-15 22:49:14.0
While a significant level of voiding can be tolerated in solder joints where electrical conductivity is the main requirement, voiding at any level severely compromises thermal conductivity. For example, in LED lighting modules effective conduction of heat through the 1st level die attach to the substrate and then through the 2nd level attach to the heat sink is critical to performance so that voiding in the solder joints at both levels must be minimized. (...) In this paper, the authors will review the factors that influence the incidence of voids in small and large area solder joints that simulate, respectively, the 1st and 2nd level joints in LED modules and discuss mitigation strategies appropriate to each level. They will also report the results of a study on the effect on the incidence of voids of flux medium formulation and the optimization of the thermal profile to ensure that most of the volatiles are released early in the reflow process.
Technical Library | 2019-01-10 10:24:47.0
We notice that the quantities of material that are to be dosed are becoming more and more divergent. In addition to large media volumes, small and very small quantities are also increasingly coming into focus. For example autonomous driving: These vehicles already produce an immense amount of data today. When potting the associated sensors, cameras, and ECUs, it is important to ensure a precise and repeatable media application – even with volumes of only 0.03 ml. In contrast, when high-voltage batteries for electric cars are potted, 5 to 10 litres of heat-conducting paste are required per vehicle – and the trend is rising. Optical bonding used in display production, on the other hand, is in the medium volume range. The challenge now is to cover the entire volume spectrum reliably and in compliance with the required cycle times. This is remedied by a modular system of scalable modules, which offers the customer the necessary flexibility and enables him to plan a system according to his needs.
Technical Library | 2019-02-06 22:02:08.0
The High Density Packaging (HDP) user group has completed a project to evaluate the majority of viable Dk (Dielectric Constant)/Df (Dissipation Factor) and delay/loss electrical test methods, with a focus on the methods used for speeds above 2 GHz. A comparison of test methods from 1 to 2 GHz through to higher test frequencies was desired, testing a variety of laminate materials (standard volume production with UL approval, low loss, and "halogen-free" laminate materials). Variations in the test board material resin content/construction and copper foil surface roughness/type were minimized. Problems with Dk/Df and loss test methods and discrepancies in results are identified, as well as possible correlations or relationships among these higher speed test methods.
Technical Library | 2019-12-26 19:13:52.0
Plated through hole (PTH) plays a critical role in printed circuit board (PCB) reliability. Thermal fatigue deformation of the PTH material is regarded as the primary factor affecting the lifetime of electrical devices. Numerous research efforts have focused on the failure mechanism model of PTH. However, most of the existing models were based on the one-dimensional structure hypothesis without taking the multilayered structure and external pad into consideration.In this paper, the constitutive relation of multilayered PTH is developed to establish the stress equation, and finite element analysis (FEA) is performed to locate the maximum stress and simulate the influence of the material properties. Finally, thermal cycle tests are conducted to verify the accuracy of the life prediction results. This model could be used in fatigue failure portable diagnosis and for life prediction of multilayered PCB.
Technical Library | 2020-01-02 12:16:02.0
A customer contacted the Helpline with the concern that parts being used in their assembly may possibly be counterfeit components. The counterfeiting of electronics components is a world-wide problem, and the threat today is even more evident than ever before. Any company, large or small, that manufactures assemblies using electronics components is equally susceptible to using counterfeit devices in their assemblies. In most cases, counterfeit components aren't discovered until after the component has already been placed on a printed circuit board (PCB), usually during first article electrical test. At this point, the only recourse is to debug the circuit to determine the faulty component and rework each PCB already in production to replace the faulty component. As one might easily surmise, this is a rather costly process; world-wide, counterfeit components account for over $15B loss in sales annually!
Technical Library | 2020-01-09 00:00:30.0
PCBs have a wide range of applications in electronics where they are used for electric signal transfer. For a multilayer build-up, thin copper foils are alternated with epoxy-based prepregs and laminated to each other. Adhesion between copper and epoxy composites is achieved by technologies based on mechanical interlocking or chemical bonding, however for future development, the understanding of failure mechanisms between these materials is of high importance. In literature, various interfacial failures are reported which lead to adhesion loss between copper and epoxy resins. This review aims to give an overview on common coupling technologies and possible failure mechanisms. The information reviewed can in turn lead to the development of new strategies, enhancing the adhesion strength of copper/epoxy joints and, therefore, establishing a basis for future PCB manufacturing.
Technical Library | 2021-06-07 19:10:16.0
The aim of this study was to compare leaching characteristics of metals from printed circuit boards (PCBs), taken from waste electrical and electronic equipment in the presence and in the absence of the iron-oxidizing bacteria, Acidithiobacillus ferrooxidans. A. ferrooxidans not only increases the leached concentration of Cu from the PCBs, but also inhibits the components of the 0K medium and leached Cu from forming precipitates such as libethenite (Cu2(PO4)(OH)), thereby assisting Cu recovery from the PCBs. In addition, the leached concentration of Pb from PCBs decreased in the presence of A. ferrooxidans, due to Pb forming amorphous precipitates. It is expected that Pb is not highly toxic to A. ferrooxidans. Consequently, A. ferrooxidans can be used as a cost-effective and environmentally friendly way to leach out valuable metals from PCBs as low-grade urban ore.
Technical Library | 2021-12-29 19:52:50.0
Medtronic seeks to quantify the thermal aging limits of electroless Ni-electroless Pd-immersion Au (ENEPIG) surface finishes to determine how aggressive the silicon burn-in process can be without loss of solderability. Silicon burn-in (power testing at elevated temperature) is used to eliminate early field failures, critical for device reliability. Thermal aging due to burn-in or annealing causes Ni and Pd diffusion to and oxidation on the surface. Surface oxides limit wetting of the PbSn solder, affecting electrical connectivity of components soldered afterburn-in. Isothermal aging of two ENEPIG surface finishes was performed at 75°C-150°C for 100 hrs-1500hrs to test the thermal aging limits and identify how loss of solderability occurs.
