Technical Library | 2008-08-20 17:28:19.0
Kitting is the first step in printed circuit board assembly. It is initiated well in advance of the actual production start to be able to prepare and deliver the kit on time. Kitting involves the gathering of all the parts needed for a particular assembly from the stockroom and issuing the kit to the manufacturing line at the right time and in the right quantity. This paper discusses kitting, describes ways to eliminate waste in different phases of kitting, and illustrates lean kitting using a case study conducted in a major contract manufacturer site.
Technical Library | 2015-04-30 20:17:03.0
Higher-speed signal transmission is increasingly required on a printed circuit board to handle massive data in electronic systems. So, signal transmission loss of copper wiring on a printed circuit board has been studied. First, total signal loss was divided into dielectric loss and conductor loss quantitatively based on electromagnetic theory. In particular, the scattering loss due to surface roughness of copper foil has been examined in detail. And the usefulness of the copper foil with low surface roughness has been demonstrated.
Technical Library | 2019-12-13 00:39:29.0
Salt spray corrosion chamber can test the ability of material and its protective layer to resist salt mist corrosion, or compare the process quality of similar protective layers, at the same time; this equipment is suitable for parts, electronic components, protective layer of metal material and other industrial products. Salt spray test is divided into neutral and acid test. What is the difference between neutral and acid in salt spray test? First, the temperature applied in the test method is different: Neutral test: a. Laboratory:35°C ±1°C, b. Saturated air drums:47°C ±1°C Acid test: a. Laboratory:50°C ±1°C, b. Saturated air drums:63°C ±1°C Second, the production material is different,neutral test chamber adoptes the traditional PVC plates, acid test chamber asopts PP sheet,which is more high temperature resistance and suits strong acid test. Third. Different test methods satisfied Neutral salt spray chamber according to GB/T 2423.17-2008, GB/T 2423.18-2000, salt spray test method and GB/T 10125-1997, GB/T 10587-2006, GB10593.2-1990, GB/T 1765-1979, GB/T 1771-2007, GB/T 12967.388, GB/T 1705.8-2008, etc. In addition to the test methods specified in the national standard, acid salt spray chamber also needs to expand the standard setting such as IEC,MIL,DIN,ASTM,IS,CNS. Last, Comparison of neutral test solutions China: NaCI distilled water solution NaCI mass concentration (50 ±5) g ≤ l pH value 6.5 ≤ 7.2 United States: distilled water solution NaCI mass concentration 5% ±1% pH value 6.5 ≤ 7.2 Germany: NaCI distilled water solution NaCI mass concentration (50 ±5) g ≤ l pH value 6.5 ≤ 7.2 Japan: NaCI distilled water solution NaCI mass concentration 5% ±1% pH pH value 6.5 ~ 7.2 France: NaCI distilled water solution NaCI mass concentration 5% pH 6.5 ≤ 7.2 https://climatechambers.com/articles&latestnews/difference-between-neutral-and-acid-salt-spray-corrosion-test.html
Technical Library | 2001-05-23 16:50:56.0
It’s not pretty out there. Companies have spent fortunes on ERP software and implementation only to find that business performance has not improved at all. These large investments and negative ROIs have created a whirlpool of controversy, rampant company politics and even a number of lawsuits. The trade press has reported many negative ERP stories, and even annual reports have pointed the finger at ERP for lower-than-expected earnings. For some, this has created a higher level of fear about making a big ERP mistake...
Technical Library | 2006-12-18 14:55:35.0
Many solder users have preconceived notions and worries involving reflow profiling guidelines. Year after year of reading profiling recommendations in industry publications, from a litany of pundits, has made it clear that perfect profiles exist and should be sought after. They feel if the solder supplier gives them a tidy drawing on a piece of paper with times and temperatures that it will magically solve all their reflow problems. This is, unfortunately, an often incorrect assumption.
Technical Library | 2010-03-04 18:11:53.0
While the electronics manufacturing industry has been occupied with the challenge of RoHS compliance and with it, Pb-free soldering, established trends of increasing functionality and miniaturization have continued. The increasing use of ultra-fine pitch and area-array devices presents challenges in both printing and flux technology. With the decrease in both the size and the pitch of said components, new problems may arise, such as head-in-pillow and graping defects
Technical Library | 2022-06-20 21:01:37.0
We've been doing a lot of print testing in our lab. In our first set of published results, "The Impact of Reduced Solder Alloy Powder Size on Solder Paste Print Performance1" from IPC/APEX 2016, we revealed a hierarchy of input variables to maximize solder paste transfer efficiency and minimize variation. In that study, we used a fully-optioned stencil as part of the equipment set. In order to tease out the data we were looking for, we could not lose critical information to the noise of stencil-induced variations.
Technical Library | 2013-05-23 17:41:21.0
Printed Electronics is considered by many international technologists to be a platform for manufacturing innovation. Its rich portfolio of advanced multi-functional nano-designed materials, scalable ambient processes, and high volume manufacturing technologies lends itself to offer an opportunity for sustained manufacturing innovation. The success of introducing a new manufacturing technology is strongly dependent on the ability to achieve high final product yields at current or reduced cost. In the past, standards have been the critical vehicles to enable manufacturing success... First published in the 2012 IPC APEX EXPO technical conference proceedings.
Technical Library | 2021-04-15 14:49:27.0
In this study, a predefined template-based image processing system is proposed to automatically detect of PCB soldering defects that negatively affect circuit operation. The proposed system consists of a scaled inspection structure, a camera, an image processing algorithm merged with Fuzzy and template guided inspection process. The prototype is produced using a plastic material, depending on the focal length of the camera and the PCB size. Image processing step comprises two steps. Firstly, solder joints are determined and boxed using Fuzzy C-means clustering algorithm.
Technical Library | 2023-10-19 22:03:14.0
Koh Young Technology, the industry leader in True 3D measurement-based inspection solutions, proudly releases another customer success story with Matric Group. This case study shows how Matric Group has leveraged their partnership with Koh Young to be one of the first in the industry to use pre-reflow AOI as a game-changer for line efficiency and improved yield. All while creating a central inspection war room to allow just one person to manage all inline inspection, increasing automation, and control and mitigating talent shortages.
