Technical Library | 2023-01-17 17:50:59.0
Heller's new Condenser Tube Flux Recovery System is designed to provide more efficient flux collection than earlier Heller flux collection systems; while providing minimal down time for inspection and cleaning. The entire system easily fits within the rear of the top shell of an 1800-EXL oven. The system utilizes a different set of top shell caps specially designed to provide the best serviceability of both the flux collection system and maintenance of the heater zone blower motors.
Technical Library | 2023-09-13 13:10:06.0
Pneumatic stencil cleaning machines are a great way to improve the efficiency and effectiveness of your stencil cleaning process. These machines use compressed air to remove contaminants and debris from stencils, which can cause defects and reliability issues.
Technical Library | 2023-09-13 13:07:16.0
Pneumatic stencil cleaning machines are a great way to improve the efficiency and effectiveness of your stencil cleaning process. These machines use compressed air to remove contaminants and debris from stencils, which can cause defects and reliability issues.
Technical Library | 2023-09-13 12:46:41.0
Online PCBA cleaning machines are a great way to improve the quality and reliability of your printed circuit boards (PCBs). These machines use a variety of methods to remove contaminants and debris from PCBs, including water, solvents, and ultrasonic waves.
Technical Library | 2023-09-13 13:03:25.0
SMT auto aqueous stencil cleaning machines are an essential tool for any SMT production line. These machines use a variety of methods to remove contaminants and debris from SMT stencils, which can cause defects and reliability issues.
Technical Library | 1999-05-09 12:36:40.0
The production of electronics began with hand soldering, followed by manual cleaning, which reached its peak during the NASA program. Each step in the process tended to be considered on a stand alone basis, without thought being given to the preceding and following steps. Since each step had its own set of specifications, this led to a "patchwork" approach to overall quality.
Technical Library | 2016-05-30 22:54:52.0
New engineered cleaning and defluxing agents promise great improvement in cleaning and reliability for electronic assemblies. As complexity grows and dimensions shrink in high reliability electronics, the need for materials compatibility and effectiveness in cleaning and rinsing is vital.
Technical Library | 2010-09-09 16:44:48.0
The effectiveness of cleaning stencils and misprinted/dirty printed circuit boards can be effectively monitored. This can be done by washing known clean circuit boards and then checking to see if they have stayed clean as a result of the washing process.
Technical Library | 2019-05-21 00:21:26.0
Continue to talk about the dust removal from temperature humidity test chamber. Cleaning and maintenance: 1) Pls remove internal impurities inisde chamber before operation. 2) The power distribution room should be cleaned at least once a year, and the dust can be removed by vacuum cleaner. 3) The exterior chamber must also be cleaned more than once a year, which can be wiped with soapy water. Inspection and maintenance of humidifier: The water storage in humidifier should be replaced once a month to ensure clean water quality, humidifying water tray should be cleaned once a month to ensure smooth flow of water. The inspection of over-temperature protector:during the test: If the temperature is over 20 ℃ ~ 30 ℃ than the maximum value setted,the power supply of the heater will stop, the "OVERHEAT" overt-emperature warning light will automatically turn on but the fan is still in operation, if the equipment runs without operator around,the operator should check the over-temperature protector in advance to ensure wether it has been setted properly before start [wet ball over-temperature protector set to 120 ℃].
Technical Library | 2008-05-14 15:44:58.0
This paper will review some basic past and present flux chemistries that affect flux collection methodology. It will also review some of the most common flux collection methods, self-cleaning techniques, and maintenance goals. And, finally, data will be presented from high volume production testing of an advanced flux management system.