Technical Library | 2015-10-08 17:40:35.0
With the push for ever improving performance on semiconductor component I/O interfaces, semiconductor components are being driven into a realm which makes them more sensitive to electrostatic discharge, potentially increasing in sensitivity by 50% every 3-5 years. Today, the majority of modern day semiconductor components are being designed to meet 250Volts of charge device model sensitivity, and that could decrease to 125Volts in the next 3-5 years, and could again decrease to 50Volts-70Volts in the following 3-5 years. The entire electronics industry must prepare for this challenge.
Technical Library | 2007-03-28 10:18:33.0
Legislation against the use of lead in electronics has been the driving force behind the use of lead-free solders, surface finishes, and component lead finishes. The major concern in using lead-free solders in the assembly and rework Chip Scale Packages (CSPs) is the relatively high temperatures that the components and the boards experience. Fine-pitch CSPs have very low standoff heights following assembly making inspection and rework of these components more difficult. One other concern pertinent to rework is the temperature of the neighboring components during rework. These issues, coupled with the limitations of rework equipment to handle lead-free reflow temperatures, make the task of reworking lead-free assemblies more challenging.
Technical Library | 2007-06-27 15:43:06.0
Traditionally most flip chips were designed with large bumps on a coarse pitch. However, as the trend towards smaller, more compact assemblies continues the sizes of semiconductor packages are forced to stay in line. New designs are incorporating smaller bump diameters on increasingly aggressive pitches, and in many cases decreasing the total IO count. With fewer and smaller bumps to distribute the load of the placement force it is becoming increasingly vital for equipment manufacturers to meet the challenge in offering low force placement solutions. One such solution will be presented in the following discussion. Also presented will be ways to minimize the initial impact spike that flip chips experience upon placement.
Technical Library | 2013-04-12 08:20:15.0
There is much to read about the shifting sands of electronics manufacturing, including current moves by OEMs to alter their EMS relationships to better mitigate risk and cost, while EMS companies look for additional ways in which to adjust their business models in an attempt to improve their profitability. Electronics outsourcing over time evolved from a means to buffer manufacturing demand fluctuations into a wide scale shift in capabilities, in part in order to deal with vastly shorter product life cycles. Following the global economic crash of 2000, aka “the internet bubble,” more and more EMS providers responded by transferring their manufacturing to low cost labour regions, and in particular China.
Technical Library | 2013-10-17 17:46:01.0
Although several commercial and experimental Pb-free solder alloys are available as replacements for Sn-Pb solders, the following families of solders are of particular interest and are the prevailing choices of industry: eutectic Sn-Ag, eutectic Sn-Cu, eutectic Sn-Zn, eutectic Bi-Sn, and Sn–In. Since the properties of the binary Pb-free solders cannot fully meet the requirements for applications in electronic packaging, additional alloying elements are added to improve the performance of these alloys. Thus, ternary and even quaternary Pb-free solders have been developed, such as Sn-Ag-Cu, Sn-Ag-Bi, and Sn-Zn-Bi solder...
Technical Library | 2018-10-03 20:41:44.0
Voids in solder joints plague many electronics manufacturers. Do you have voids in your life? We have good news for you, there are many excellent ways to "Fill the Void." This paper is a continuation of previous work on voiding in which the following variables were studied: water soluble lead-free solder pastes, a variety of stencil designs, and reflow profiles. Quad Flat No-Lead (QFN) component thermal pads were used as the test vehicle. The voiding results were summarized and recommendations were made for reduction of voiding.
Technical Library | 2018-11-20 21:33:57.0
There are several industry-accepted methods for determining the reliability of flux residues after assembly. The recommended methods of test sample preparation do not always closely mimic the thermal cycle experienced by an assembly. Therefore, extraction from actual assemblies has become a popular method of process control to assess consistency of post-reflow cleanliness. Every method of post-reflow flux residue characterization will depend on the reflow process followed to prepare the coupon.This investigation will focus on the effect of thermal conditions on the remainder of active ingredients in flux residues after assembly with no-clean solder pastes.
Technical Library | 2022-01-03 14:55:55.0
Follow Ted as he learns about the Maintenance Planner Scheduler job description in the excerpt below from the full Maintenance Planning and Scheduling course PowerPoint download. The course PowerPoint starts out teaching Ted that the Maintenance Planner Scheduler job opening is much more than being a preventive maintenance planner or being a maintenance repair person. As you will learn here, the potential planner needs to learn the big picture first. Like applying Lean Six Sigma principles and methodologies. © 2021 - Ref: https://bin95.com/articles/maintenance-management/preventive-maintenance-planner.htm
Technical Library | 2022-01-05 23:20:33.0
This study aims to present the characterization of five different types of printed circuit boards (PCBs) for use in future recycling processes. PCBs used: motherboards, lead free motherboards, video cards, memory and printer cards. The comminution of the circuit boards was performed using blade mills and hammer mills with 9mm and 6mm meshes, respectively. Throughout the physical processing, analysis was made with stereoscopic optics to ensure that the correct materials had been released. The pre-magnetic separation parts were given a granulometric classification followed by acid digestion and loss on ignition tests.
Technical Library | 2023-03-13 19:12:56.0
Printed electronics (PE) is impacting almost every branch of manufacturing. The printing of electronics on mechanically flexible substrates such as plastic, paper and textile, using traditional printing techniques, provides novel applications for wearable and stretchable electronics. Government sponsored consortiums, universities, contract printers, startups and global manufacturers are developing processes to bring this technology to market faster, more costeffectively and at scale. By increasing the speed of technology adoption while following industrialization best practices, industry researchers aim to create processes that ramp up the scale of production for simple circuits and integrated conductive structures.
