Technical Library: glenbrook technologies inc. (Page 2 of 10)

Microscopy in Failure Analysis

Technical Library | 2019-09-03 17:06:09.0

Both optical and scanning electron microscopy (SEM) are powerful tools for failure analysis in electronics and are used for low and high magnification examination. This article will provide detailed, step by step information for examining solder joints.

ACI Technologies, Inc.

The Power Packaging Laboratory at ACI Technologies

Technical Library | 2019-05-31 14:21:59.0

Microelectronics is the manufacture of systems built from extremely small electronic components. In today’s electronic world, devices must be portable, equipped with wireless technology and are driven by size, weight, power, and cost (SWaP-C). These system level drivers are crucial to all current and future electronic applications from personal computers and cellular telephones to military-fielded hardware, biomedical instrumentation, and space-flight hardware.

ACI Technologies, Inc.

Flip Chip Attach Techniques

Technical Library | 2019-05-21 17:38:55.0

Last month we presented Flip Chip Rework.As promised, this month we follow up with attachment techniques. Flip chip assembly is a key technology for advanced packaging of microelectronic circuits. It allows attachment of a bare chip to a packaging substrate in a face-down configuration, with electrical connections between the chip and substrate via conducting “bumps.” Flip chip technology was first invented by IBM for mainframe computer application in the early 1960s. Semiconductor devices are mounted face down and electrically and mechanically connected to a substrate (Figure 1). IBM called this manufacturing process a C4 process (controlled collapse chip connection).

ACI Technologies, Inc.

Selective Soldering and the Modular Approach

Technical Library | 2019-08-08 10:23:51.0

High mix production is the mainstay of many electronics assembly plants. Lot sizes and board complexities vary and the boards are often mixed technology, comprising a blend of both surface mount and through-hole technology. Modularizing a production line enables a clear distinction between one type of assembly process and another. This article assumes a modern factory where a job can be routed to the selective soldering machine module, the hand assembly bench, or a combination of both. The decision rules of routing a circuit board through hand assembly versus automated selective soldering are discussed. Hand assembly soldering operations require no explanation.

ACI Technologies, Inc.

Manufacturing Cost Reduction through Automation

Technical Library | 2019-06-24 15:54:17.0

Defense systems and its manufacturers are often blamed for not embracing new and innovative technologies to manufacture products compared to its commercial counterparts. Commercial product manufacturers are known to think “outside the box” in coming up with new products which are cheaper, have fewer parts, and easier to manufacture using automation. Automation leads to consistent quality products which are reliable and reproducible. Implementing some of these producibility design practices into defense systems will greatly reduce the cost and insertion time for new products.

ACI Technologies, Inc.

Computer Aided Design, Manufacturing, and Engineering

Technical Library | 2019-07-01 10:44:11.0

In the electronics industry of today, companies emphasize better quality, lower cost, and shorter lead time on their products in order to keep up with their competitors. ACI Technologies (ACI) has been utilizing Computer Aided Design (CAD), Computer Aided Manufacturing(CAM), and Computer Aided Engineering (CAE) in its development of advanced electronics systems. CAD utilizes computer systems to assist in the creation, modification, analysis, and optimization of a design [1].

ACI Technologies, Inc.

Thermal Interface Materials Testing

Technical Library | 2019-05-30 11:04:03.0

There exists a need to efficiently remove heat from power electronics within power systems to enhance performance. Thermal management is a critical function to that operation. Reducing the junction temperature of semiconductor power electronic devices enables them to operate at higher currents. Lowering operating temperatures reduces the thermal stress on electronic devices, which improves efficiency and reduces failures. To improve the heat removal process, the current heat transfer design of a power system has been analyzed and a variety of thermal interface materials (TIMs) and cold plate technologies have been evaluated. This paper will review some of these results.

ACI Technologies, Inc.

COTS Cooling

Technical Library | 2019-05-31 14:15:01.0

ACI Technologies (ACI) is working on a project where one of the challenges is removing a large quantity of heat from audio amplifier circuits. This challenge is further complicated in that the heat generating circuits are located in a rack mounted box that needs to be shielded from electro-magnetic interference (EMI). Mechanically, this means that there cannot be open passages into the rack mounted box. We will first review the basic types of cooling available as commercial off-the-shelf (COTS) systems for the electronics industry, then discuss the pros and cons of each for different applications, and finally reveal the criteria and solution for the ACI project.

ACI Technologies, Inc.

SMT Component Reliability for RF Applications

Technical Library | 2019-05-31 14:19:24.0

ACI Technologies (ACI) characterized the reliability of surface mount RF components. The RF frequency band of interest was the X band (10.7 to 11.7GHz). A two pronged test for reliability of circuit card assemblies (CCA) was designed for both extreme thermal cycling and vibration. The rapid thermal cycling and extreme vibration testing simulates the total stress encountered by the assembly over the life of the product but accomplishes it in a relatively short period of time. In order to perform the reliability testing, a test vehicle consisting of a printed circuit board with test structures and components, was designed, fabricated, and assembled at ACI.

ACI Technologies, Inc.

Corrosion Analysis

Technical Library | 2019-06-03 15:32:40.0

ACI Technologies was pleased to assist a customer by conducting elemental analysis on several assemblies displaying severe corrosion. Several board assemblies had failed in the field and exhibited areas of corrosion in close proximity to onboard components. The most common source of corrosion on electronic assemblies is residual flux. Fluxes are specific chemistries applied during the soldering process which improve the wetting of the solder to both the pad and component when forming the solder joint. They can be highly reactive chemicals that, if left on the assemblies, can lead to corrosion, electrical degradation, and decreased reliability. In the presence of moisture and electrical bias, flux residue can enable dendritic growth as a result of electrochemical migration (ECM).

ACI Technologies, Inc.


glenbrook technologies inc. searches for Companies, Equipment, Machines, Suppliers & Information

Heller Industries Inc.
Heller Industries Inc.

Reflow ovens for automated SMT PCB assembly, specializing in lead free processing and nitrogen reflow. The best convection reflow ovens on the market.

Manufacturer

4 Vreeland Rd.
Florham Park, NJ USA

Phone: 973-377-6800

SMT spare parts - Qinyi Electronics

Wave Soldering 101 Training Course
Selective soldering solutions with Jade soldering machine

High Precision Fluid Dispensers
Equipment Auction Automotive Electronics Supplier - Closure of Tier-One SMT Dvision: (10) ASM & Universal SMT Lines & Feeders Equipment as-new-as 2019! Dek | Koh Young | Speedline | Vitronics | Viscom

World's Best Reflow Oven Customizable for Unique Applications