Technical Library | 2020-11-10 15:43:25.0
Flexible hybrid electronics (FHE) interface rigid electronic components with flexible sensors, circuits, and substrates. This paper reports the reliability improvement of a FHE Human Performance Monitor (HPM), designed to monitor electrocardiography (ECG) signals.
Technical Library | 2017-07-13 16:16:27.0
Controlled humidity and temperature controlled surface insulation resistance (SIR) measurements of flux covered test vehicles, subject to a direct current (D.C.) bias voltage are recognized by a number of global standards organizations as the preferred method to determine if no clean solder paste and wave soldering flux residues are suitable for reliable electronic assemblies. The IPC, Japanese Industry Standard (JIS), Deutsches Institut fur Normung (DIN) and International Electrical Commission (IEC) all have industry reviewed standards using similar variations of this measurement. (...) This study will compare the results from testing two solder pastes using the IPC-J-STD-004B, IPC TM-650 2.6.3.7 surface insulation resistance test, and IPC TM-650 2.3.25 in an attempt to investigate the correlation of ROSE methods as predictors of electronic assembly electrical reliability.
Technical Library | 2013-02-14 12:54:29.0
Boundary-scan (1149.1) technology was originally developed to provide a far easier method to perform digital DC testing to detect intra-IC interconnect assembly faults, such as solder shorts and opens. Today's advanced IC technology now includes high-speed differential interfaces that include AC or DC coupling components loaded on the printed circuit assembly. Simple stuck-at-high/low test methods are not sufficient to detect all assembly fault conditions, which includes shorts, opens and missing components. Improved diagnostics requires detailed circuit analysis, predictive assembly fault simulation and more complex testing to isolate and accurately detect all possible assembly faults... First published in the 2012 IPC APEX EXPO technical conference proceedings
Technical Library | 2015-04-30 20:17:03.0
Higher-speed signal transmission is increasingly required on a printed circuit board to handle massive data in electronic systems. So, signal transmission loss of copper wiring on a printed circuit board has been studied. First, total signal loss was divided into dielectric loss and conductor loss quantitatively based on electromagnetic theory. In particular, the scattering loss due to surface roughness of copper foil has been examined in detail. And the usefulness of the copper foil with low surface roughness has been demonstrated.
Technical Library | 2012-06-27 18:26:34.0
First published in the 2012 IPC APEX EXPO technical conference proceedings. Signal integrity analysis has shown that printed circuit board (PCB) insertion loss is a key factor affecting high speed channel performance. Determining and controlling PCB inser
Technical Library | 2009-04-09 20:43:09.0
Evidence has come to light that increased solder process temperatures, specifically for lead free solder, are dramatically shortening life expectancy of components; failures do not show up during initial test, but much later on in the products life,
Technical Library | 2021-02-25 14:19:00.0
This study proposes a new design of lightweight and cost-e#14;cient composite materials for the aeronautic industry utilizing recycled fresh scrap rubber, epoxy resin, and graphene nanoplatelets (GnPs). After manufacturing the composites, their bending strength and fracture characteristics were investigated by three-point bending (3PB) tests. Halpin–Tsai homogenization adapted to composites containing GnPs was used to estimate the moduli of the composites, and satisfactory agreement with the 3PB test results was observed.
Technical Library | 2009-04-30 18:06:24.0
This presentation surveys the most significant via and via-related laminate failure mechanisms from past to present using data from current induced thermal cycling (CITC) testing, failure analysis, and other sources. The relative life and failure modes of thru vias, buried vias, and microvias (stacked vs. non-stacked) are compared, along with the affect of structure, materials, and peak temperatures on the above. The origin of via-induced laminate failures such as "eyebrow cracks" and Pb free related internal delamination is also explored.
Technical Library | 1999-07-20 11:00:12.0
It's quite common for a power supply (PSU) designer to work with a circuit designer to realize a system design compliant with international EMC regulations. PSU designers will be well aware of the requirement of the power supply to provide clean DC voltage and not disturb the AC mains voltage. However, they may not have any idea of the noise that can potentially be introduced to the mains through the PSU by the target circuit. Likewise, the circuit designers (digital or analogue) may not know what attenuation the PSU will provide.
Technical Library | 2017-04-06 16:50:56.0
Silicon photonics is an IC technology where data is transferred using light that is routed on the chip using optical waveguides (Figure 1). Silicon photonics is best known as a method to solve problems with high input/output bandwidth applications. For example, because of ever-growing bandwidth requirements in datacenters, the optical transmit and receive heads are being placed closer and closer to the board and the IC. But, designers also apply this technology to biosensors, medical diagnostics, and environmental monitoring. Regardless of the application, photonic ICs always need integration to electronic circuits and this results in unique challenges.
Midwest Circuit Technology provides Carbide Router Bits and End Milling Cuters for use in PCB Depaneling equipment. We have over 35 years of supplying tools and machining experience in drilling, Routing, Test Fixture manufacture.
114 Barrington Town Square
Aurora, OH USA
Phone: 13309956900
.gif)
.gif)
