Technical Library | 2007-07-24 11:47:54.0
The rapid technical development of ultrashort laser systems is creating exciting possibilities for very precise localization of laser energy in time and space. These achievements have triggered novel laser applications based on nonlinear interaction processes. A promising three-dimensional microfabrication method that has recently attracted considerable attention is based on two-photon polymerization with ultrashort laser pulses.
Technical Library | 2008-03-25 18:15:54.0
Thin film thermoelectric devices offer a fundamentally new operating regime for integrated, active cooling solutions and localized thermal management, yet the assembly methodology used to implement these devices is fully compatible with existing surface mount approaches. In order to take advantage of these unique characteristics, thin film thermoelectric devices need to be designed for the appropriate thermal and form-factor environments, with system-level constraints carefully considered as an integral part of the overall design process.
Technical Library | 2011-11-03 18:04:07.0
This paper presents the development of a novel vehicle-routing-based algorithm for optimizing component pick-up and placement on a collect-and-place type machine in printed circuit board manufacturing. We present a two-phase heuristic that produces soluti
Technical Library | 2017-12-11 22:31:06.0
Typical printed circuit board assemblies (PCBAs) processed by reflow, wave, or selective wave soldering were analysed for typical levels of process related residues, resulting from a specific or combination of soldering process. Typical solder flux residue distribution pattern, composition, and concentration are profiled and reported. Presence of localized flux residues were visualized using a commercial Residue RAT gel test and chemical structure was identified by FT-IR, while the concentration was measured using ion chromatography, and the electrical properties of the extracts were determined by measuring the leak current using a twin platinum electrode setup. Localized extraction of residue was carried out using a commercial C3 extraction system. Results clearly show that the amount and distribution of flux residues are a function of the soldering process, and the level can be reduced by an appropriate cleaning. Selective soldering process generates significantly higher levels of residues compared to the wave and reflow process. For conformal coated PCBAs, the contamination levels generated from the tested wave and selective soldering process are found to be enough to generate blisters under exposure to high humidity levels.
Technical Library | 2020-01-01 17:06:52.0
The majority of electronic failures occur due to thermally induced stresses and strains caused by excessive differences in coefficients of thermal expansion (CTE) across materials.CTE mismatches occur in both 1st and 2nd level interconnects in electronics assemblies. 1st level interconnects connect the die to a substrate. This substrate can be underfilled so there are both global and local CTE mismatches to consider. 2nd level interconnects connect the substrate, or package, to the printed circuit board (PCB). This would be considered a "board level" CTE mismatch. Several stress and strain mitigation techniques exist including the use of conformal coating.
Technical Library | 2013-01-29 15:48:08.0
Choosing a new wire Cutting and Stripping (C&S) machine can be like shopping for a new car. With so many choices, where does one start? A nice, little sports car might be fun to have, but how often will it just sit there because it can’t carry a car load of kids or some odd-sized goods from the local home improvement store? You just might be better off with a midsize SUV that does a pretty good job at doing everything you need it to do.
Technical Library | 2013-09-05 17:44:14.0
Surface plasmon polaritons (SPPs) are localized surface electromagnetic waves that propagate along the interface between a metal and a dielectric. Owing to their inherent subwavelength confinement, SPPs have a strong potential to become building blocks of a type of photonic circuitry built up on 2D metal surfaces; however, SPPs are difficult to control on curved surfaces conformably and flexibly to produce advanced functional devices. Here we propose the concept of conformal surface plasmons (CSPs), surface plasmon waves that can propagate on ultrathin and flexible films to long distances in a wide broadband range from microwave to mid-infrared frequencies.
Technical Library | 2021-09-21 20:36:45.0
The present paper gives an overview of surface failures, internal nonconformities and solders joint failures detected by microscopic analysis of electronic assemblies. Optical microscopy (stereomicroscopy) and Fourier-Transform- Infrared (FTIR) microscopy is used for documentation and failure localization on electronic samples surface. For internal observable conditions a metallographic cross-section analysis of the sample is required. The aim of this work is to present some internal and external observable nonconformities which frequently appear in electronic assemblies. In order to detect these nonconformities, optical microscopy, cross section analysis, FTIR-microscopy and scanning electron microscopy with energy dispersive spectrometry (SEM-EDS) were used as analytical techniques.
Technical Library | 2021-11-22 20:32:10.0
The aim of this work is to define a procedure to develop diagnostic systems for Printed Circuit Boards, based on Automated Optical Inspection with low cost and easy adaptability to different features. A complete system to detect mounting defects in the circuits is presented in this paper. A low cost image acquisition system with high accuracy has been designed to fit this application. Afterward, the resulting images are processed using the Wavelet Transform and Neural Networks, for low computational cost and acceptable precision. The wavelet space represents a compact support for efficient feature extraction with the localization property. The proposed solution is demonstrated on several defects in different kind of circuits.
Technical Library | 2019-04-24 20:06:51.0
Choosing an outsourced manufacturing partner that is perfect for a new product and close to your design team is quite different to choosing a partner that can manufacture that same product in volume in lower cost locations and fulfill globally. This is where the Gateway model comes into its own. Most large EMS have structured their organizations to leverage proximity to OEM design teams in high cost regions while providing the benefits of low cost regions for volume manufacturing. The "Gateway" facility in higher cost regions provides design engineering, supply chain design, prototype, and NPI services. The goal of the Gateway is to develop an effective build recipe that can then be effectively and seamlessly transferred to one or more volume manufacturing facility that offers lower costs and direct fulfillment to consumers.We will present a case study that highlights the value of this model and that shows some of the key elements that allow for seamless transitions from plant to plant. The Gateway model is an essential element to a successful global manufacturing model and helps ensure that products are made in the right geography.
