Technical Library | 2010-04-15 22:06:32.0
As electronic products increase in functionality and complexity, there is an emphasis on affordability, miniaturization, and energy efficiency. The telecommunications, automotive, and commercial electronic markets are the leading drivers for these trends. These markets see high volume manufacturing with millions of units priced to the fraction of the cent. The choice of the packaging material for the electrical components for these markets can have a substantial effect on the cost of the final product. Therefore plastic encapsulated components are almost universally used in non-military applications over the conventional ceramic or metal electronic packages.
Technical Library | 2012-10-25 16:34:02.0
First published in the 2012 IPC APEX EXPO technical conference proceedings. This paper will examine stencil technologies (including Laser and Electroform), Aperture Wall coatings (including Nickel-Teflon coatings and Nano-coatings), and how these parameters influence paste transfer for miniature devices with Area Ratios less than the standard recommended lower limit of .5. A matrix of print tests will be utilized to compare paste transfer and measure the effectiveness of the different stencil configurations. Area Ratios ranging from .32 to .68 will be investigated.
Technical Library | 2013-05-09 14:35:18.0
Atmospheric dust consists of solids suspended in air. Dust is well known for its complex nature. It normally includes inorganic mineral materials, water soluble salts, organic materials, and a small amount of water. The impact of dust on the reliability of printed circuit board assemblies (PCBAs) is ever-growing, driven by the miniaturization of technology and the increasing un-controlled operating conditions with more dust exposure in telecom and information industries... First published in the 2012 IPC APEX EXPO technical conference proceedings.
Technical Library | 2014-03-27 14:50:01.0
Because of the phase out of CFC's and HCFC's, standard solder pastes and fluxes evolved from RA and RMA fluxes, to No-Clean, to low residue No-Clean, to very low residue No-Clean. Many companies came out with their cleaning solutions, aqueous and semi-aqueous, with each product release being more innovative than the previous one. Unfortunately for most of the suppliers of cleaners, two other trends appeared; lead-free soldering and the progressive miniaturization of electronic devices.
Technical Library | 2016-04-28 14:43:23.0
Underfilling is a long-standing process issued from the micro-electronics that can enhance the robustness and the reliability of first or second-level interconnects for a variety of electronic applications. Its usage is currently spreading across the industry fueled by the decreasing reliability margins induced by the miniaturization and interconnect pitch reduction. (...) This paper will address the control of surface mount under filled assemblies, focusing on applicable inspection techniques and possible options to overcome their limitations.
Technical Library | 2016-06-21 09:15:31.0
The trends in mobile electronics today are smaller, thinner and lighter. Yet, mobile devices are more powerful than ever. Applications, like wireless internet connections, RFID and Bluetooth, that have become essential in today’s devices, require more complex transmission mechanisms. As a result, manufacturers find themselves faced with the challenge of working with ultra-miniature RF cable assemblies.
Technical Library | 2017-11-08 23:22:04.0
Due to the ongoing trend towards miniaturization of power components, the need for increased thermal conductivity of solder joints in SMT processes gains more and more importance. Therefore, the role of void free solder joints in power electronics becomes more central. Voids developed during soldering reduce the actual thermal transfer and can cause thermal damage of the power components up to their failure. For this reason, the company has developed a new technique to minimize the formation of these voids during the soldering process.
Technical Library | 2018-03-05 11:22:48.0
Growing demands for smaller electronic assemblies has resulted in reduced sizes of passive components, requiring the introduction of newer components, such as the 01005 devices. Component miniaturization presents significant challenges to the traditional surface mount assembly process. A successful assembly solution for these 01005 devices should be repeatable and reproducible, and should include guidelines for (i) the selection of solder paste and (ii) appropriate stencil and substrate pad design, and should ensure strict process control standards.
Technical Library | 2022-02-16 15:34:32.0
Because of the phase-out of CFCs and HCFCs, standard solder pastes and fluxes evolved from RA and RMA fluxes to No-Clean, to low residue No-Clean, to very low residue No-Clean. Many companies came out with their cleaning solutions, aqueous and semi-aqueous, with each product release being more innovative than the previous one. Unfortunately for most of the suppliers of cleaners, two other trends appeared; lead-free soldering and the progressive miniaturization of electronic devices
Technical Library | 2023-03-13 19:06:53.0
Purpose – There has been increasing interest in the development of printable electronics to meet the growing demand for low-cost, large-area, miniaturized, flexible and lightweight devices. The purpose of this paper is to discuss the electronic application of novel printable materials. Design/methodology/approach – The paper addresses the utilization of polymer nanocomposites as it relates to printable and flexible technology for electronic packaging. Printable technology such as screen-printing, ink-jet printing, and microcontact printing provides a fully additive, non-contacting deposition method that is suitable for flexible production.
