Technical Library | 2006-11-01 22:37:23.0
Flip Chip Plastic Ball Grid Array (FCPBGA) modules, when subjected to extreme environmental stress testing, may often reveal mechanical and electrical failure mechanisms which may not project to the field application environment. One such test can be the Deep Thermal Cycle (DTC) environmental stress which cycles from -55°C to 125°C. This “hammer” test provides the customer with a level of security for robustness, but does not typically represent conditions which a module is likely to experience during normal handling and operation.
Technical Library | 2012-12-12 03:17:51.0
When we designed the PCB equipments, we should try to simplify crcuit and structure design that on the premise of ensuring the equipments to meet the technology and performance, In modern society, modules design (MD)is a effective measures to improved the pcb equipment reliability. The system were made up simpleness functions of modules to reducing the complexity of the design. Both domestic and abroad, a large number of facts have proved this point, MD was a best choice for PCB equipment design.
Technical Library | 2019-01-30 21:20:47.0
Due to the arrayed nature of the Computed Tomography (CT) Detector, high density area array interconnect solutions are critical to the functionality of the CT detector module. Specifically, the detector module sensor element, hereby known as the Multi-chip module (MCM), has a 544 position BGA area array pattern that requires precise test stimulation. A novel pogo-pin block array and corresponding motorized test socket has been designed to stimulate the MCM and acquire full functional test data. (...) This paper and presentation will focus on the socket design challenges and also key learnings from the design that can be applied to general test systems, including reliability testing. The secondary focus will be on the overall data collection and graphical user interface for the test equipment.
Technical Library | 2020-11-19 20:35:26.0
Simultaneously with the first complex electronic circuits, the task of creating effective means of diagnosing and repairing them appeared. In previous decades, specialized programmable stands were used for diagnostics of serial electronic products, as well as various testers and probes for troubleshooting during their operation. But the dramatic increase in the density / cost factor, in parallel with the very rapid modification of electronic products, made programmable stands economically ineffective even in mass production. The use of traditional laboratory equipment (oscilloscopes, multimeters, etc.) requires power supply to the defective modules, which is often impossible and unsafe, since it can lead to failure of the working modules of the module. In addition, the use of this equipment requires documentation and highly qualified personnel. More automated and sophisticated signature analysis systems came to the rescue in solving this problem. A feature of these devices is that they allow you to test digital and analog assemblies without dismantling components and without supplying voltage.
Technical Library | 2009-09-18 14:48:58.0
The stencil cleaner can be one of the most versatile tools on the manufacturing floor. It can be used to clean electronic modules in various stages of the manufacturing process. In fact, an automated stencil cleaner can clean just about anything you come up against in your PCB assembly process.
Technical Library | 2001-04-24 10:38:38.0
Many PCB designers are interested in taking advantage of Multichip Modules, but are unfamiliar with the technology. While the design process is very much the same, MCM manufacturing processes vary dramatically. MCM routing requirements are dictated by the manufacturing process and types of components. Components mounted on MCM substrates are predominantly, if not exclusively, bare chips. As a result, the component body and I/O pins are no longer constrained to industry standard pin counts and form factors as are packaged components...
Technical Library | 2017-11-15 22:49:14.0
While a significant level of voiding can be tolerated in solder joints where electrical conductivity is the main requirement, voiding at any level severely compromises thermal conductivity. For example, in LED lighting modules effective conduction of heat through the 1st level die attach to the substrate and then through the 2nd level attach to the heat sink is critical to performance so that voiding in the solder joints at both levels must be minimized. (...) In this paper, the authors will review the factors that influence the incidence of voids in small and large area solder joints that simulate, respectively, the 1st and 2nd level joints in LED modules and discuss mitigation strategies appropriate to each level. They will also report the results of a study on the effect on the incidence of voids of flux medium formulation and the optimization of the thermal profile to ensure that most of the volatiles are released early in the reflow process.
Technical Library | 2022-02-09 17:52:47.0
This article presents the first time that an millimeter-wave (mm-wave) multichip module (MCM) with on-demand "smart" encapsulation has been fabricated utilizing additive manufacturing technologies. RF and dc interconnects were fabricated using inkjet printing, while the encapsulation was realized using 3-D printing. Inkjet-printed interconnects feature superior RF performance, better mechanical reliability, and on-demand, low-cost fabrication process.
Technical Library | 2007-05-17 16:44:37.0
In the quest for quality, selecting the right Statistical Process Control (SPC) Software system doesn't boil down to a simple functional "fit-to-requirements" anymore. Once the expert domain of highly focused, independent software developers, the competitive landscape has changed dramatically with the influx of big-name ERP software providers who are aggressively promoting integrated quality modules within an all-encompassing business application framework.
Technical Library | 2016-11-23 00:26:50.0
As we wirelessly connect more and more devices to the Internet, electronics engineers face several challenges, including how to package a radio transmitter into their existing device real estate and how to make increasingly smaller devices. They’re also striving to meet consumer demand for Internet of Things (IoT) products that are ergonomically easy to use and unobtrusive to the environment. This whitepaper explores the challenges that come with designing connected devices into increasingly smaller products, specifically antenna integration, and how system-inpackage modules can help.
.jpg)
