Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
Technical Library | 2021-01-06 20:28:58.0
Cavity technology in a Printed Circuit Board (PCB) has existed for many years. The methodology to create the cavity in the PCB has evolved over time as technologies have advanced and the manufacturing process varies by the individual PCB
Technical Library | 2012-05-31 18:01:31.0
First published in the 2012 IPC APEX EXPO technical conference proceedings. Considering technological advances in multi-depth cavities in the PCB manufacturing industry, various subtopics have materialized regarding the processing and application of such
Technical Library | 2023-05-10 01:39:38.0
DPC (DirectPlatingCopper) thin film process is a method of prepare copper film using magnetron sputtering technology. This process is a process in which the copper target with the target material is placed in a true cavity chamber, and plasma is generated on the copper target surface by magnetron sputtering technology. The ions in the plasma are bombarded on the surface of the target, which is sputtered into fine particles and deposited on the substrate to form a copper film.
Technical Library | 2010-08-19 17:50:32.0
This article looks at each of the roles of the engineer and PCB designer, considers the traditional design process, and makes suggestions on how the designer can contribute significantly to improving a design’s overall signal integrity while simultaneousl
Technical Library | 2012-12-12 03:17:51.0
When we designed the PCB equipments, we should try to simplify crcuit and structure design that on the premise of ensuring the equipments to meet the technology and performance, In modern society, modules design (MD)is a effective measures to improved the pcb equipment reliability. The system were made up simpleness functions of modules to reducing the complexity of the design. Both domestic and abroad, a large number of facts have proved this point, MD was a best choice for PCB equipment design.
Technical Library | 2006-07-14 11:48:11.0
The perennial question in electronics design and manufacture is: "How do I design a printed circuit board (PCB) so that it can be properly tested?" To achieve this objective, there are a number of design-for-test (DFT) considerations and techniques. Some are major, others, minor. However, the total contributes to a highly effective PCB design so that testing procedures applied to a given design result in high 90 percent plus test coverage.
Technical Library | 2010-12-16 16:59:09.0
This report discusses the significance of heat management in the design of printed circuit boards (PCB). After an introduction into the basics of PCBs the crucial mechanisms of heat transfer are discussed with regard to significance and typical design par
Technical Library | 2018-02-14 22:58:54.0
This document describes general guidelines and attention points for PCB design regarding selective soldering. The guidelines can be applied for Select Wave and/or Multi Wave soldering process in both leaded and leadfree alloy. When a PCB is designed according to these guidelines, a stable and solid solder-process can be guaranteed.
Technical Library | 2010-01-27 19:22:04.0
This paper reviews one of the single most important, but sometimes overlooked or taken for granted, aspects of the electronics industry – The PCB Design Grid System
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830