Technical Library | 2023-05-02 19:03:34.0
The demand for 0201 components in consumer products will increase sharply over the next few years due to the need for miniaturization. It is predicted that over 20 billion 0201 components will be used in more than one billion cell phones worldwide by the year 2003. Therefore, research and development on 0201 assembly is becoming a very hot topic. The first step to achieve a successful assembly process is to obtain a good PCB design for 0201 packages. This paper presents the data and criteria of PCB design for 0201 packages, including the pad design for 0201 components, and the minimum pad spacing or component clearance between 0201 components or between 0201 and other components. A systematic study on pad design and pad spacing was undertaken, using two test vehicles and three Design of Experiments (DOEs). In the first DOE, 2 out of 18 types of 0201 pad designs were selected based on process yield. The second DOE was focused on pad spacing, including 10mil, 8mil, 6mil and 4mil. The third experiment was final optimization, using two types of optimized pad designs with 10mil, 8mil and 6mil pad spacing. Through the above experiments, the design guideline for PCB layout for 0201 packages and the assembly process capability are identified.
Technical Library | 2006-10-02 14:26:47.0
This paper addresses the assembly and reliability of 0.5 mm pitch leadless Chip Scale Packages (CSP) on .062" immersion Ag plated printed circuit boards (PCB) using Pb-free solder paste. Four different leadless CSP designs were studied and each was evaluated using multiple PCB attachment pad designs.
Technical Library | 2008-02-04 12:13:38.0
Engineers are always striving to make a lighter, faster and stronger PCB. In order to achieve their designs, engineers must turn to alternative materials to enhance their designs. There are many materials that allow for thermal, coefficient of thermal expansion (CTE) and rigidity. Many times if a material enables an engineer to have CTE they will have to sacrifice thermal. Currently carbon composite laminates are being used in order to achieve an ideal PCB with thermal, CTE and rigidity with almost no weight premiums.
Technical Library | 2018-08-01 11:25:59.0
With complexities of PCB design scaling and manufacturing processes adopting to environmentally friendly practices raise challenges in ensuring structural quality of PCBs. This makes it essential to have a good 'Design for Test' (DFT) to ensure a robust structural test. (...)During the course of the DFT review, can we realize a good test strategy for the PCBA. How can the test strategy of the PCBA be partitioned as to what portions of the design can be covered structurally and what is covered functionally, in a way that provides best diagnostics to discover faults
Technical Library | 2017-11-14 15:30:04.0
Can you put a product that hasn't been fully tested on the market? When it comes to Printed Circuit Board (PCB) assembly and manufacturing, most firms’ answer is neither a strict yes or no.
Technical Library | 2012-07-19 21:24:02.0
First published in the 2012 IPC APEX EXPO technical conference proceedings. With the ever accelerating demands in printed circuit board (PCB) design, the choices of advanced laminate materials have become fewer and fewer. The trends continue towards high
Technical Library | 2016-11-08 16:47:18.0
Over time most PCB designs need to change – a mistake is found, or a part becomes obsolete, etc. Typically once the changes are complete, a new set of manufacturing files (Gerbers, NC Drill files, BOM, Pick and Place, etc) are generated, and the updated design is stored as separate version within a version control system. Using a version control system makes it possible for design teams to go back later and compare differences between design versions. ****** http://www.numericalinnovations.com/blogs/news/gerber-comparisons-between-revisions-of-the-same-board *****
Technical Library | 2012-12-26 20:18:50.0
①Single side The basic flexible printed circuit board is used of substrate of single side pcb materials and coated coverlay after finishing printed. ②Double sided That is made of substrates of double sided printed circuit board with double surface coated coverlays after finishing printed. ③Single copper foil with double coverlays Single copper foil coated different coverlays with double surface after finishing printed. ④Air gap Laminating two single printed circuit board together with no glue and bare design to meet high flexibility requirements. ⑤Multilayer That is designed for three and above circuit layers by laminating single side printed circuit board or double sided printed circuit board. ⑥COF IC chips and electronic components are installed on the flexible circuit board directly. ⑦Rigid-Flexible PCB Combined to rigid PCB with supporting and flexible PCB with high flexibility.
Technical Library | 2011-04-07 14:50:29.0
Quad Flat No Leads (QFN) package designs receive more and more attention in electronic industry nowadays. This package offers a number of benefits including (1) small size, such as a near die-sized footprint, thin profile, and light weight; (2) easy PCB t
Technical Library | 2021-12-21 23:21:34.0
Points of discussion in "HDI Microvia Technology – Cost Aspects" are: - Reasons for the use of HDI technology - Printed circuit board (PCB) size - Number of layers - Stack-up and complexity - Other important cost influences -–Design rules -–Drilling costs -–Microvia filling
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
