Technical Library | 2009-10-29 11:45:52.0
The globalization of markets results in stronger competition with clearly noticeably cost pressure. For companies producing electronic equipment it is therefore of existential importance to reduce production costs whilst maintaining a consistently high quality level of the manufactured products. Manual repair soldering that is expensive, time-consuming and cost intensive is already unacceptable due to the required quality and the reproducibility of the whole manufacturing process.
Technical Library | 2014-03-27 14:50:01.0
Because of the phase out of CFC's and HCFC's, standard solder pastes and fluxes evolved from RA and RMA fluxes, to No-Clean, to low residue No-Clean, to very low residue No-Clean. Many companies came out with their cleaning solutions, aqueous and semi-aqueous, with each product release being more innovative than the previous one. Unfortunately for most of the suppliers of cleaners, two other trends appeared; lead-free soldering and the progressive miniaturization of electronic devices.
Technical Library | 2017-11-08 23:22:04.0
Due to the ongoing trend towards miniaturization of power components, the need for increased thermal conductivity of solder joints in SMT processes gains more and more importance. Therefore, the role of void free solder joints in power electronics becomes more central. Voids developed during soldering reduce the actual thermal transfer and can cause thermal damage of the power components up to their failure. For this reason, the company has developed a new technique to minimize the formation of these voids during the soldering process.
Technical Library | 2018-08-03 14:37:59.0
In the electronics industry, the quality and reliability of any product is highly dependent upon the capabilities of the manufacturing suppliers. Manufacturing defects are one of the top reasons why companies fail to meet warranty expectations. These problems can result in severe financial pain and eventual loss of market share. What a surprising number of engineers and managers fail to realize is that focusing on processes addresses only part of the issue. Supplier selection also plays a critical role in the success or failure of the final product.
Technical Library | 2020-08-05 18:41:32.0
With the first 5G NR standard recently approved by the 3GPP at the end of 2017, many companies are racing to design 5G radio products that will demand wider bandwidths, higher frequencies, enhanced carrier aggregation and support of massive MIMO. AT&T and Samsung plan to launch 5G mobile services and Verizon plans to launch 5G Fixed Wireless Access in the US this year while South Korea will be demonstrating 5G at the upcoming Winter Olympics.
Technical Library | 2017-11-01 17:06:38.0
Over fifteen years has passed since North America and Europe ceased being the center of worldwide PCB fabrication, and were supplanted by a Far East market with low cost labor, more relaxed environmental requirements, and strong government support. In just a few short years, the superior cost advantages of this new dynamic put volume PCB production in the West out of business, aside for the military and specialty technology applications contained in the few shops that continue to exist today.Recently, however, the conditions which created the current equilibrium appear to be shifting again. In this new dynamic, automation, innovative green wastewater technologies, and next generation process equipment innovations have combined to make new factories capable of achieving rapid ROI for PCB fabrication almost anywhere. This paper means to illustrate this new dynamic, and provide case study examples from the new greenfield installation at the company captive facility in New Hampshire.
Technical Library | 2020-01-02 12:16:02.0
A customer contacted the Helpline with the concern that parts being used in their assembly may possibly be counterfeit components. The counterfeiting of electronics components is a world-wide problem, and the threat today is even more evident than ever before. Any company, large or small, that manufactures assemblies using electronics components is equally susceptible to using counterfeit devices in their assemblies. In most cases, counterfeit components aren't discovered until after the component has already been placed on a printed circuit board (PCB), usually during first article electrical test. At this point, the only recourse is to debug the circuit to determine the faulty component and rework each PCB already in production to replace the faulty component. As one might easily surmise, this is a rather costly process; world-wide, counterfeit components account for over $15B loss in sales annually!
Technical Library | 2022-03-16 19:41:17.0
Creep corrosion occurs in electronics assemblies and it is reminiscent to electromigration but does not require electrical field to drive the reaction. Corrosive elements and moisture must be present for creep corrosion to occur. Sulfur is the most prominent element to cause creep corrosion in environments such as paper mills, rubber manufacturing, mining, cement manufacturing, waste water treatment etc., also including companies and locations nearby such industries. The main part of printed circuit board assembly (PCBA) to be affected is the PCB surface finish. Especially immersion silver is prone to creep corrosion, but it sometimes occurs in NiPd (lead frames), and to a lesser extent in ENIG and OSP surface finishes. As the use of immersion silver is increasing as PCB surface finish and electronics are more and more used in harsh environments, creep corrosion is a growing risk. In this paper we will present the driving forces and mechanisms as well as suitable tests and mitigation strategies against creep corrosion
Technical Library | 2011-10-06 13:59:04.0
The desire to have more functionality into increasingly smaller size end products has been pushing the PCB and IC Packaging industry towards High Density Interconnect (HDI) and 3D Packaging (stacked dies, embedded packaged components). Many companies in the high-end consumer electronics market place have been embedding passive chip components on inner PCB and IC Packages for a few years now. However, embedding packaged components on inner layers has remained elusive for the broader market due to lack of proper design tools and high cost of embedding components on inner layers (...) This paper will highlight several key industrialization aspects addressed in the frame of the European funded FP7 HERMES* project to build a manufacturing environment for products with embedded components. The program entered its third year and is now dealing with the manufacturing of functional demonstrators as an introduction to industrialization.
Technical Library | 2016-06-16 15:29:31.0
Embedding components within the PC board structure is not a new concept. Until recently, however, most embedded component PC board applications adapted only passive elements. The early component forming processes relied on resistive inks and films to enable embedding of resistor and capacitors elements. Although these forming methods remain viable, many companies are choosing to place very thin discrete passive components and semiconductor die elements within the PC board layering structure. In addition to improving the products performance, companies have found that by reducing the component population on the PC board's surface, board level assembly is less complex and the PC board can be made smaller, The smaller substrate, even when more complex, often results in lower cost. Although size and cost reductions are significant attributes, the closer coupling of key elements can also contribute to improving functional performance.This paper focuses on six basic embedded component structure designs described in IPC-7092.
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
