Technical Library | 2010-07-15 19:19:56.0
When reworking more complex SMT components such as finer pitch SMT components, SMTconnectors and even area array devices, the most common method of printing on the printing selectively on the PCB has some serious shortcomings. The most significant problem
Technical Library | 2013-05-30 17:33:26.0
This paper covers the following topics: The Measurement Application, Measurement Requirements, Measurement Problems, Measurement Results, Reference Samples, Conclusions
Technical Library | 2012-04-05 22:53:10.0
In this paper we show how hybrid control and modeling tech-niques can be put to work for solving a problem of industrial relevance in Surface Mount Technology (SMT) manufacturing. In particular, by closing the loop over the stencil printing process, we ob
Technical Library | 2013-10-22 07:38:42.0
In conformal coating many components and printed circuit board locations must remain uncoated due to the insulating nature of the coating. The purpose of the conformal coating masking materials is to prevent migration of the conformal coatings into components that need to clear and designated keep out areas. This applies to both liquid conformal coating and Parylene processing. Get this basic process wrong and it can be a big problem, leading to the next stage of either repairing the conformal coating leak, stripping the conformal coating off the circuit board, removing a component to replace it or scrapping the board. This paper reviews typical masking application methods in conformal coating and provides advice on minimising problems.
Technical Library | 2024-01-08 21:31:01.0
The aim of this collection and interpretation is to develop an understanding of moisture in materials, especially in printed circuit boards, to know the effects on further processing and to be able to derive targeted corrective actions when moisture-related problems occur. In principle, the considerations are valid for all types of PCBs. Although these basic principles are of particular importance when working with flexible and rigid-flexible printed circuit boards; observing them can mean the difference between success or failure.
Technical Library | 2010-03-04 18:11:53.0
While the electronics manufacturing industry has been occupied with the challenge of RoHS compliance and with it, Pb-free soldering, established trends of increasing functionality and miniaturization have continued. The increasing use of ultra-fine pitch and area-array devices presents challenges in both printing and flux technology. With the decrease in both the size and the pitch of said components, new problems may arise, such as head-in-pillow and graping defects
Technical Library | 2016-09-06 04:54:27.0
Printed circuit boards are the base of electronic products in a variety of consumer and industrial applications. New PCBs always perform well. However, their performance will deteriorate with time due to exposure to different environmental conditions like condensation, moisture, contamination of the iconic material on the surface, dust and dirt, mildew, alpha particles, etc. To avoid these problems, PCBs are protected with conformal coatings. Let’s see how this is done, and how they protect PCB components.
Technical Library | 2020-03-19 00:23:15.0
In this study, the question was how to perform statistically reliable robust- ness tests for the non-contact drop-on-demand printing of functional fluids, such as solder paste and conductive adhesives. The goal of this study was to develop a general method for hypothesis testing when robustness tests are performed. The main problem was to determine if there was a statistical difference between two means or proportions of jet printing devices. In this study, an example of jetting quality variation was used when comparing two jet printing ejector types that differ slightly in design. We wanted to understand if the difference in ejector design can impact jetting quality by performing robustness tests. and thus answer the question, "Can jetting differences be seen between ejector design 1 and design 2"?
Technical Library | 2021-06-07 19:03:05.0
The waste from end-of-life electrical and electronic equipment has become the fastest growing waste problem in the world. The difficult-to-treat waste-printed circuit boards (WPCBs), which are nearly 3−6 wt % of the total electronic waste, generate great environmental concern nowadays. For WPCB treatment and recycling, the mechanical−physical method has turned out to be more technologically and economically feasible. In this work, the mechanical−physical treatment and recycling technologies for WPCBs were investigated, and future research was directed as well. Removing electric and electronic components(EECs) from WPCBs is critical for their crushing and metal recovery; however, environmentally friendly and high-efficiency removal techniques need be developed. Concentrated metals rich in Cu, Al, Au, Pb, and Sn recovered from WPCBs need be further refined to add to their economic values. The low value added nonmetallic fraction of waste-printed circuit boards (NMF-WPCBs) accounts for approximately 60 wt % of the WPCBs. From the perspective of environmental management, a zero-waste approach to recycling them should be developed to gain values. Preparing polymer composites and geopolymers offers many advantages and has potential applications in various fields, especially as construction and building materials. However, the mechanical and thermal properties of NMF-WPCBs composites should be further improved for preparing polymer composites. Surface modification or filler blending could be applied to improve the interfacial comparability between NMF-WPCBs and the polymer matrix. The NMFWPCBs shows potential in preparing cement mortar and geological polymers, but the environmental safety resulting from metals needs to be taken into account. This study will provide a significant reference for the industrial recycling of NMF-WPCBs
Technical Library | 2020-06-19 19:08:14.0
The designs of electronic devices and systems are being continuously improved by becoming smaller in size and faster in communication speed. The potential risk associated with these specific design improvements will be an increase in power density and, consequently, a greater risk of thermal problems and failures. At the same time, the prevailing use of circuit boards integrated with power devices such as motor controllers and drivers, light-emitting diode (LED) lighting modules, power supplies, and amplifiers, and regulators for TV, etc., drive to the use of a proper thermal management system while designing these kinds of printed circuit board (PCB).
.gif)
