Technical Library | 2019-05-21 17:31:39.0
In the field of electronics manufacturing, the end use of the product will always dictate the processes, procedures, and methods, not only for building the product, but also for testing, cleaning, and protecting the assembly in order to assure the level of quality required for proper operation. The need to protect an electronic assembly from its end use environment may stem from anyone of a number of hazardous (or potentially hazardous) conditions. Choosing the type of protective material is dependent upon matching that material’s characteristics with the conditions to be overcome. Naturally, the use of a protective (conformal) coating will require some method of verification to ensure the desired level and type of protection is achieved.
Technical Library | 2010-05-12 16:21:05.0
Numerous studies have shown that greater than 60% of end of line defects in SMT assembly can be traced to solder paste and the printing process. Reflowing adds another 15% or so. In light of this fact, it is surprising that no simplified procedure for solder paste evaluation has been documented. This paper is about such a procedure.
Technical Library | 2020-03-08 11:35:53.0
A sample for Larry Bush's Maintenance Policies and Procedures - 2nd Edition (A 415-page book in PDF format. Those who purchase also receive 150 support files in editable format to customize and use as samples and templates.)
Technical Library | 2018-06-04 13:52:05.0
Potting in a vacuum or atmospheric conditions? This question about the correct procedure concerns many users, among others i.e. electronics manufacturers, who pot more and more complex parts and components for a huge variety of products. Against the actual requirements of product and process, a decision on the procedure is often made under the assumption: „Potting under atmosphere = affordable and easy" and „Potting under vacuum = expensive and difficult". But that's a thing of the past. The way to the correct method, however, requires the clarification of a number of factors.
Technical Library | 2021-03-18 20:03:27.0
Much has been said and written about the accuracy of visual attribute inspections of potentially counterfeit components. The techniques and procedures being used to inspect counterfeit and reworked electronic components in the open marketplace can be quite effective in most cases.
Technical Library | 2006-07-14 11:48:11.0
The perennial question in electronics design and manufacture is: "How do I design a printed circuit board (PCB) so that it can be properly tested?" To achieve this objective, there are a number of design-for-test (DFT) considerations and techniques. Some are major, others, minor. However, the total contributes to a highly effective PCB design so that testing procedures applied to a given design result in high 90 percent plus test coverage.
Technical Library | 2018-02-01 00:31:48.0
This paper briefly summarizes the technologies underpinning the evolution in electrical system diagnosis and repair, which include schematic layout automation using prototypes and rule-based styling, instant language translation, 2D/3D view links with schematics, interactive diagnostic procedures, and dynamically-generated signal-tracing diagrams. These technologies empower after-sales service teams with state-of-the-art capabilities, which not only reduce costs but also improve brand quality in the eyes of its customers.
Technical Library | 2018-11-29 13:43:54.0
Ionic contamination testing as a process control tool a newly developed testing protocol based on IPC-TM 650 2.3.25, was established to enable monitoring of ionic contamination within series production. The testing procedure was successfully implemented within the production of high reliability, safety critical electronic circuits, involving multiple production sites around the world. I will be shown in this paper that the test protocol is capable for meeting Six-Sigma-Criteria.
Technical Library | 2022-08-17 01:21:54.0
Back in the "good old days," stencil cleaning was effortless and effective. CFC-based solvents were sprayed or wiped onto a stencil with apertures hundreds of times larger than modern-day components. The stencil cleaning process was not considered a value-added procedure; instead it was the cleaning of a production tool. How times have changed. The late-1980s ushered in the end of most of the popular solvents, and the machines that consumed them. Assemblers turned to alternative cleaning agents, including IPAs and other solvents.
Technical Library | 2023-06-12 18:52:18.0
This paper will review stencil design requirements for printing solder paste around and in through-hole pads / openings. There is much interest in this procedure since full implementation allows the placement of both through-hole components as well as SMD's and the subsequent reflow of both simultaneously. This in turn eliminates the need to wave solder or hand solder through-hole components.
