Technical Library | 2018-03-05 11:22:48.0
Growing demands for smaller electronic assemblies has resulted in reduced sizes of passive components, requiring the introduction of newer components, such as the 01005 devices. Component miniaturization presents significant challenges to the traditional surface mount assembly process. A successful assembly solution for these 01005 devices should be repeatable and reproducible, and should include guidelines for (i) the selection of solder paste and (ii) appropriate stencil and substrate pad design, and should ensure strict process control standards.
Technical Library | 2009-02-13 12:29:39.0
To meet the market demand for a best-in-class, low-cost leadfree alloy for wave, selective and dip soldering
Technical Library | 1999-08-05 09:31:04.0
This document provides suggested standard contents for equipment reference manuals for semiconductor process equipment. It includes a generic and detailed outline for equipment manuals, with major sections on installing, operating, controlling, and integrating process equipment.
Technical Library | 2013-10-13 10:54:13.0
The measurement of the conformal coating thickness on a printed circuit board (PCB) to ensure internal and international standards are met is now a critical factor in conformal coating process control. There are several methods for measurement of conformal coating thickness and they fall into two categories. These categories are wet film measurements applied during coating application and dry film measurements made after the coating is dried enough not to damage the coating.
Technical Library | 2007-05-17 16:44:37.0
In the quest for quality, selecting the right Statistical Process Control (SPC) Software system doesn't boil down to a simple functional "fit-to-requirements" anymore. Once the expert domain of highly focused, independent software developers, the competitive landscape has changed dramatically with the influx of big-name ERP software providers who are aggressively promoting integrated quality modules within an all-encompassing business application framework.
Technical Library | 2007-01-03 16:36:58.0
Solder paste dispensing is not a new process. However, today's microelectronics present a daunting array of technical challenges to meet deposit size requirements. The need for better paste formulations, more precise equipment, and more tightly controlled processes is driving paste suppliers and equipment suppliers to develop new methods and materials. The most challenging solder paste deposits are those smaller than 0.25mm in diameter and today’s electronics demand such deposits. This paper addresses the process requirements for solder paste micro-deposits in terms of material, equipment and process variable control required for success in producing 0.25mm and smaller deposits.
Technical Library | 2012-11-12 14:06:48.0
With consumers constantly looking for lower prices on their technology products and manufacturers trying to squeak out higher margins from their production lines, the need for process control and lower overhead costs have become even more important. One sector that is often overlooked is the hand soldering area of the factory. Many factories have been struggling with antiquated soldering systems for years. In some cases they are trying to make their investment in stations last much longer than they were designed for, or they are falsely trying to recoup their original investment ‐ all at the cost of higher operating expenses or even worse, reduced operator thru‐put.
Technical Library | 2018-11-20 21:33:57.0
There are several industry-accepted methods for determining the reliability of flux residues after assembly. The recommended methods of test sample preparation do not always closely mimic the thermal cycle experienced by an assembly. Therefore, extraction from actual assemblies has become a popular method of process control to assess consistency of post-reflow cleanliness. Every method of post-reflow flux residue characterization will depend on the reflow process followed to prepare the coupon.This investigation will focus on the effect of thermal conditions on the remainder of active ingredients in flux residues after assembly with no-clean solder pastes.
Technical Library | 2015-05-28 17:34:48.0
The printed circuit board assembly industry has long embraced the "Smaller, Lighter, Faster" mantra for electronic devices, especially in our ubiquitous mobile devices. As manufacturers increase smart phone functionality and capability, designers must adopt smaller components to facilitate high-density packaging. Measuring over 40% smaller than today's 0402M (0.4mmx0.2mm) microchip, the new 03015M (0.3mm×0.15mm) microchip epitomizes the bleeding-edge of surface mount component miniaturization. This presentation will explore board and component trends, and then delve into three critical areas for successful 03015M adoption: placement equipment, assembly materials, and process controls. Beyond machine requirements, the importance of taping specifications, component shape, solder fillet, spacing gap, and stencil design are explored. We will also examine how Adaptive Process Control can increase production yields and reduce defects by placing components to solder position rather than pad. Understanding the process considerations for 03015M component mounting today will help designers and manufacturers transition to successful placement tomorrow.
Technical Library | 2007-11-08 17:35:46.0
A continuous furnace is ideal for processes requiring high production volumes, process consistency, and precision control. This overview discusses some of the newer temperature and atmosphere capabilities of continuous furnaces and addresses the various components that make up a continuous furnace.
winsouce.jpg)
