Technical Library | 2020-06-19 19:08:14.0
The designs of electronic devices and systems are being continuously improved by becoming smaller in size and faster in communication speed. The potential risk associated with these specific design improvements will be an increase in power density and, consequently, a greater risk of thermal problems and failures. At the same time, the prevailing use of circuit boards integrated with power devices such as motor controllers and drivers, light-emitting diode (LED) lighting modules, power supplies, and amplifiers, and regulators for TV, etc., drive to the use of a proper thermal management system while designing these kinds of printed circuit board (PCB).
Technical Library | 2008-12-03 19:39:00.0
This paper presents the analysis from a recent printing study employing a test vehicle that includes components such as 01005s to QFPs. In a recent publication, part of this study was presented focusing on 01005 printing only. This printing process was determined to be suitable for 01005s assembly and also analyzed based on statistical capability. The current paper will present the results from additional detailed analysis to determine if this process has the capability to provide sufficient solder paste deposits for larger components located on the same test board. In the future, the SMT industry may always look towards “Broadband Printing” as an alternative to dual stencil or stepped stencil printing technologies in order to meet the needs of both small and large components.
Technical Library | 2009-09-18 14:52:06.0
Electronic assembly cleaning processes are becoming increasingly more complex because of global environmental mandates and customer driven product performance requirements. Manufacturing strategies today require process equivalence. That is to say, if a product is made or modified in different locations or processes around the world, the result should be the same. If cleaning is a requirement, will existing electronic assembly cleaning processes meet the challenge? Innovative cleaning fluid and cleaning equipment designs provide improved functionality in both batch and continuous inline cleaning processes. The purpose of this designed experiment is to report optimized cleaning process parameters for removing lead-free flux residues on populated circuit assemblies using innovative cleaning fluid and batch cleaning equipment designs.
Technical Library | 2012-12-20 14:36:09.0
The increased function of personal electronic devices, such as mobile phones and personal music devices, has driven the need for smaller and smaller active and passive components. This trend toward miniaturization, occurring at the same time as the conversion to RoHS-compliant lead-free assembly, has been a considerable challenge to the electronics assembly industry. The main reason for this is the higher reflow process temperatures required for Pb-free assembly. These higher temperatures can thermally damage the PCB and the components. In addition, the higher reflow temperatures can negatively affect the solder joint quality, especially when coupled with the smaller paste deposits required for these smaller components. If additional thermal processing is required, the risk increases even more. First Published at SMTA's International Conference on Soldering and Reliability in Toronto, May 2011
Technical Library | 2014-09-18 16:48:26.0
Two major drivers in electronic industry are electrical and mechanical miniaturization. Both induce major changes in the material selection as well as in the design. Nevertheless, the mechanical and thermal reliability of a Printed Circuit Board (PCB) has to remain at the same high level or even increase (e.g. multiple lead-free soldering). To achieve these reliability targets, extensive testing has to be done with bare PCB as well as assembled PCB. These tests are time consuming and cost intensive. The PCBs have to be produced, assembled, tested and finally a detailed failure analysis is required to be performed.This paper examines the development of our concept and has the potential to enable the prediction of the lifetime of the PCB using accelerated testing methods and finite element simulations.
Technical Library | 2015-01-26 15:30:00.0
In 2005 Raytheon Technical Services Company, now Raytheon Information, Intelligence and Services (Raytheon IIS), approached Ensil regarding the repair of their manufactured Radar Control Terminal (RCT) units. The RCT TRS P/N 13563090-2, a key component in the AN/MPQ-64 Sentinel System, consisted of outdated parts which caused minor to major unit failures. Ensil repaired the RCT's at every turn, correcting any component with the parts still in circulation (mother boards, displays, power supplies) to provide the client with the best available technology. These repairs were completed to military standards and kept the RCT effective, allowing for the Sentinel radar to remain operational. However, the supply of outdated parts was eventually no longer available. Ensil offered the best possible solution, utilizing the skills of their knowledgeable engineering staff, they would reverse engineer a new computer to replace the obsolete RCT while maintaining the same form, fit and function.
Technical Library | 2015-06-30 16:07:12.0
Robotics for automated fluid dispensing have the ability to apply a variety of materials including epoxy, silicone, and acrylic coatings. These materials are extensively used in today’s high-speed fluid dispensers for the electronics industry. Whether a dispenser is applying epoxy or another material, the central concept for applying any form of material remains the same. Specific points of an item being dispensed onto are programmed into the dispensing system. The automated fluid dispensers software interprets the programmed information and keeps the travel path in memory. A robotic arm moves fluid dispensing nozzles along this travel path and applies epoxy onto the surface of the item with precise accuracy. Machine speed can be adjusted to emit varying amounts of epoxy. The overall application process is auto-regulating and will not be disrupted.
Technical Library | 2017-08-02 20:18:21.0
In this rapidly moving electronics market, fast to market with new products is what separates top performing companies from average companies. A survey conducted by Arthur D. Little revealed that "New-Product Development (NPD) productivity in atop performing company is five times what it is in the average company. The top performer gets five times as much new product output for the same investment." What do they know that the rest of us do not? One winning factor is the use of the Robert Cooper process. (...)This paper will present a Lean Six Sigma approach to "right sizing" the Stage Gate process to be efficient, practical, and easy to manage. Various tools of Stage Gate, along with proven best practice, will be covered. In addition, a reduced Stage Gate model will be discussed for simple, low risk projects.
Technical Library | 2018-03-15 07:23:35.0
The SMT assembly process is continuously challenged by the factors which enhance circuit board performance and limit productivity. The pick and place and reflow systems reflect these driven issues by adding more and more controls to their systems, but the fact is one of the age old processes continues to operate within the same rules since the dawn of the SMT assembly world: The SMT screen printing. (...)This paper showcases a new stencil process that was discovered by reverting to the basics:understanding the reason for each stencil material process, focusing on detailed finishes and a disciplined aperture design process, maintaining original designs, and making the correctly designed apertures to control the paste deposition. The test results drove us to focus the efforts on the aperture walls In this paper we will demonstrate with lab tests SMT process results howthe improved paste release results in improved SMT print process performance and its positive impact on SPI yields and EOL performance.
Technical Library | 2021-05-06 13:48:05.0
In this paper most commonly occurring Bare PCB defects such as Track Cut, Track short and Pad Damages are detected by Image processing techniques. Reference PCB without having any defects is compared with test PCB having defects to identify the defects and x-y coordinates of the center of the defects along with radii are obtained using Difference of Gaussian method and location of the individual type of defects are marked either by similar color or different colors. Result Analysis includes time taken for the inspection of a single defect, multiple similar defects, and multiple different defects. Time taken is ranging from 1.674 to 1.714 seconds if the individual type of defects are marked by different colors and 0.670 to 0.709 seconds if all the identified defects are marked by the same colors.
