Technical Library | 2019-05-29 23:10:30.0
There are times when a PCB prototype needs to be built quickly to test out a design. In such cases where it is known early on that there will be multiple iterations or that a "one and done" assembly will be made that there will be some SMT assemblers who choose to hand print solder paste onto the board using a "frameless" stencil. In such cases where hand printing is used, the consistency of the printing technique has typically been in question. Furthermore, the effectiveness of both the nanocoatings as well as the higher end stainless steel materials, which have been heretofore studied in controlled printing environments, will be evaluated for their impact on the hand printing process.The purpose of the study was to determine the effectiveness of select nanocoating materials as well as certain high end stainless steel stencil materials as they relate to the manual SMT printing process. A variety of nanocoatings were applied to SMT metal stencils and solder paste volume measurements were taken to compare the effectiveness.
Technical Library | 2007-02-01 09:57:15.0
The rapid assimilation of Ball Grid Array (BGA) and other Area Array Package technology in the electronics industry is due to the fact that this package type allows for a greater I/O count in a smaller area while maintaining a pitch that allows for ease of manufacture.
Technical Library | 2007-01-31 15:17:04.0
The goal of this project is to evaluate the reliability of lead-free BGA solder joints with a variety of different pad sizes using several different BGA rework methods. These methods included BGAs reworked with both flux only and solder paste attachment techniques and with or without the use of the BEST stay in place StencilQuick™. The daisy chained test boards were placed into a thermal test chamber and cycled between -25ºC to 125ºC over a 30 minute cycle with a 30 minute dwell on each end of the cycle. Each BGA on the board was wired and the continuity assessed during the 1000 cycles the test samples were in the chamber.
Technical Library | 2013-07-03 10:31:54.0
It has been demonstrated in numerous pieces of work that stencil printing, one of the most complex PCB assembly processes, is one of the largest contributors to defects (Revelino et el). This complexity extends to prototype builds where a small number of boards need to be assembled quickly and reliably. Stencil printing is becoming increasingly challenging as packages shrink in size, increase in lead count and require closer lead spacing (finer pitch). Prototype SMT assembly can be further divided between industrial and commercial work and the DIYer, hobbyist or researcher groups. This second group is highly price sensitive when it comes to the materials used for the board assembly as their funds are sourced from personal or research monies as opposed to company funds. This has led to development of a lower cost SMT printing stencil made from plastic film as opposed to the more traditional stainless steel stencil used by industrial and commercial users.This study compares the performance of these two traditional materials and their respective impact on solder paste printing including efficiency and print quality.
Technical Library | 2023-05-22 17:13:17.0
Agenda Overview Independent Testing & Studies-Print studies -Understencil Wipe studies-Durability Testing-Ongoing Studies NanoClear Product Information NanocoatingsComparison Summary Questions
Technical Library | 2013-01-11 16:51:33.0
There have been claims in the industry that laser-cut electroformed nickel foil blanks provide stencil print performance comparable to electroformed stencils. A study was established to measure the quantitative differences in performance between the two during an independent lab study.
Technical Library | 2023-03-13 19:40:21.0
The present work explores the effects of paper properties on conventional silver-based conducting inks. The effects of smoothness, relative humidity, porosity, permeability and wettability on electrical properties of silver inks on different paper substrates were studied. Another objective of this work was to prepare and study polyaniline synthesized in the presence of different lignosulfonates.
Technical Library | 2023-04-17 21:25:52.0
Outline/Agenda * Introduction of Ionics and ROSE * Evolution in technology * Rev H in the IPC-J-STD-001 * Real World Case Study * Conclusions
Technical Library | 1999-08-05 09:34:44.0
This document demonstrates a sequential process of evaluating automated wafer instruments and discusses why this approach is useful for studying instruments that have automation features such as loading and focusing mechanisms. The methodology specifies a series of experiments consisting of two or more capability studies followed by a stability study. Each experiment achieves a separate goal, yet combines with the others in providing information needed to assess the usefulness of the instrument.
Technical Library | 2006-10-26 08:08:00.0
There have been many studies of the causes of tombstoning; some published, some not. They tend to focus on a single process parameter as the root cause of tombstoning. However, there is no single process change that is a sure cure for tombstoning! Those that claim otherwise are either uninformed or trying to sell you something. Rather than limiting your view to a single solution, EFD recommends you heed all of the studies. Like pieces of a puzzle, each study does not reveal the whole picture, but looked at all together, the picture is clear.
