Technical Library: through-hole robotic systems (Page 1 of 2)

PCB Fabrication Processes and Their Effects on Fine Copper Barrel Cracks

Technical Library | 2015-12-23 16:57:27.0

The onset of copper barrel cracks is typically induced by the presence of manufacturing defects. In the absence of discernible manufacturing defects, the causes of copper barrel cracks in printed circuit board (PCB) plated through holes is not well understood. Accordingly, there is a need to determine what affects the onset of barrel cracks and then control those causes to mitigate their initiation.The objective of this research is to conduct a design of experiment (DOE) to determine if there is a relationship between PCB fabrication processes and the prevalence of fine barrel cracks. The test vehicle used will be a 16-layer epoxy-based PCB that has two different sized plated through holes as well as buried vias.

Raytheon

Selective soldering in an optimized nitrogen atmosphere

Technical Library | 2021-09-29 13:35:21.0

In PCB circuit assemblies the trend is moving to more SMD components with finer pitch connections. The majority of the assemblies still have a small amount of through hole (THT) components. Some of them can't withstand high reflow temperatures, while others are there because of their mechanical robustness. In automotive applications these THT components are also present. Many products for cars, including steering units, radio and navigation, and air compressors also use THT technology to connect board-to-board, PCB's to metal shields or housings out of plastic or even aluminium. This is not a simple 2D plain soldering technology, as it requires handling, efficient thermal heating and handling of heavy (up to 10 kg) parts. Soldering technology becomes more 3D where connections have to be made on different levels. For this technology robots using solder wire fail because of the spattering of the flux in the wires and the long cycle time. In wave soldering using pallets the wave height is limited and pin in paste reflow is only a 2D application with space limitations. Selective soldering using dedicated plates with nozzles on the solder area is the preferred way to make these connections. All joints can be soldered in one dip resulting in short cycle times. Additional soldering on a small select nozzle can make the system even more flexible. The soldering can only be successful when there is enough thermal heat in the assembly before the solder touches the board. A forced convection preheat is a must for many applications to bring enough heat into the metal and board materials. The challenge in a dip soldering process is to get a sufficient hole fill without bridging and minimize the number of solder balls. A new cover was designed to improve the nitrogen environment. Reducing oxygen levels benefits the wetting, but increases the risk for solder balling. Previous investigations showed that solder balling can be minimized by selecting proper materials for solder resist and flux.

Vitronics Soltec

The Pin-in-Paste (or AART) Process for Odd Form and Through Hole Printed Circuit Boards

Technical Library | 2007-09-27 16:18:15.0

Considerable interest exists in the process known as the pinin- paste, or the Alternative Assembly and Reflow Technology (AART) process. The AART process allows for the simultaneous reflow of both odd-form and through hole devices as well as surface mount components. This process has several advantages over the typical mixed technology process sequence that includes wave soldering and/or hand soldering, often in addition to reflow soldering.

Universal Instruments Corporation

A New Line Balancing Method Considering Robot Count and Operational Costs in Electronics Assembly

Technical Library | 2019-05-02 13:47:39.0

Automating electronics assembly is complex because many devices are not manufactured on a scale that justifies the cost of setting up robotic systems, which need frequent readjustments as models change. Moreover, robots are only appropriate for a limited part of assembly because small, intricate devices are particularly difficult for them to assemble. Therefore, assembly line designers must minimize operational and readjustment costs by determining the optimal assignment of tasks and resources for workstations. Several research studies address task assignment issues, most of them dealing with robot costs as fixed amount, ignoring operational costs. In real factories, the cost of human resources is constant, whereas robot costs increase with uptime. Thus, human workload must be as large and robot workload as small as possible for the given number of humans and robots. We propose a new task assignment method that establishes a workload balancing that meet precedence and further constraints.

Fujitsu Laboratories Ltd.

The Proximity of Microvias to PTHs And Its Impact On The Reliability

Technical Library | 2007-05-09 18:26:16.0

High Density Interconnect (HDI) technology is fast becoming the enabling technology for the next generation of small portable electronic communication devices. These methods employ many different dielectrics and via fabrication technologies. In this research, the effect of the proximity of microvias to Plated Through Holes (PTHs) and its effect on the reliability of the microvias was extensively evaluated. The reliability of microvia interconnect structures was evaluated using Liquid-To-Liquid Thermal Shock (LLTS) testing (-55oC to +125oC). Comprehensive failure analysis was performed on microvias fabricated using different via fabrication technologies.

Universal Instruments Corporation

Selective soldering in an optimized nitrogen atmosphere

Technical Library | 2023-11-14 19:24:08.0

In PCB circuit assemblies the trend is moving to more SMD components with finer pitch connections. The majority of the assemblies still have a small amount of through hole (THT) components. Some of them can't withstand high reflow temperatures, while others are there because of their mechanical robustness. In automotive applications these THT components are also present. Many products for cars, including steering units, radio and navigation, and air compressors also use THT technology to connect board-to-board, PCB's to metal shields or housings out of plastic or even aluminium. This is not a simple 2D plain soldering technology, as it requires handling, efficient thermal heating and handling of heavy (up to 10 kg) parts. Soldering technology becomes more 3D where connections have to be made on different levels. For this technology robots using solder wire fail because of the spattering of the flux in the wires and the long cycle time. In wave soldering using pallets the wave height is limited and pin in paste reflow is only a 2D application with space limitations.

Vitronics Soltec

Selective Soldering: A Cost-Effective Alternative to Wave Soldering

Technical Library | 2023-11-14 19:33:57.0

Wave soldering is an established technology and is commonly used where large unit volumes occur with low product variety. However, if a wave soldering machine is getting old or if technological changes or new PCB designs limits its manufacturing capabilities, consideration should be given to whether selective soldering would be a better choice. Anyone who deals with soldering through-hole and surface mount mixed-technology printed circuit assemblies will quickly discover that a selective soldering machine is not only less expensive that wave soldering, but selective soldering also offers the opportunity to meet customer requirements with significantly more flexibility. One such company is Thomas Preuhs GmbH. Located in Geislingen, Germany, Thomas Preuhs GmbH manufactures a variety of electronic assemblies for solar and HVAC data systems, automotive and white goods products as well as electric drive systems.

Nordson Corporation

Essentials about Printed Circuit Board Assembly

Technical Library | 2019-10-18 10:37:25.0

It usually does not make any logic to invest in costly fabrication equipment in case you just desire to spin some prototypes and rather outsource your Printed Circuit Board assembly as well as prototype fabrication to a trustworthy vendor. I would provide a few tips as to what to consider when seeking a contract manufacturer. The two most common procedures associated with Printed Circuit Board Assembly are through-hole technology and surface mount technology. Talking about the difference between through-hole technology and surface mount technology. Through-hole elements have metal leads, & these metal leads are supplied through-plated holes inside the circuit board. On the other hand, SMT elements might or might not have leads, nevertheless most significantly, they are developed to be soldered onto the surface of the circuit boards straight on the same side as the element body. A lot of contract manufacturers would provide a quick quote mechanism over their site for the fabrication of circuit boards as well as assembly of prototypes. This would bank your time when comparing various vendors. Ensure that the quote system facilitates you to fill your details, for instance, board material, thickness, copper thickness, milling, etc. in order that you can avail of a precise quote devoid of any surprises afterward. And this is quite necessary. Typically the cost per board would decline as quality upgrades. This is owing to the fairly high setup price of circuit board fabrication over and above component assembly. A few vendors would employ a system where they unite boards from various consumers. This manner the setup price would be circulated among numerous clients. When you fabricate an item, you clearly don’t desire to have to fabricate a big quantity of boards straight away whilst you improve your design. One restriction with small quantity prototypes though is that the option of materials & material thicknesses would be constrained. In case you are employing a particular material then opportunities are there will not be any other clients employing the same material. Additionally, lead time plays a major role in indecisive prices. A longer lead time facilitates the fabricator more liberty in slotting your fabrication. This is basically reflected in cheaper prices that would view in the quote section. Clearly, if you are in a hurry and desire to be moved to the summit of the pile you would require splurging more dollars. Ensure that your contract fabricator would support the file sort for producing which you offer. The most general format for printed circuit board fabrication is the Gerber format nonetheless a few vendors would moreover embrace board files from general printed circuit board software products. A few suppliers also provide in house printed circuit design. Even in case, you create your board yourself, choosing a vendor with design services might prove resourceful in case there is an issue with your files. In this scenario, your vendor could make swift changes that would neglect pricey delays. If you are looking for an Electronic Manufacturing Services (EMS Assembly) provider, then the web is the best to search.

Optima Technology Associates, Inc.

Choosing the Right Valve for a Selective Robotic Conformal Coating Application Process

Technical Library | 2013-10-13 10:29:59.0

When investigating the option of a selective conformal coating process it is crucial to consider the right robotic system and valve combination for the material and circuit board that you wish to coat. To fail to do this can lead to difficult process problems in the production line. This article reviews the various valves available and how they can be used with the typical conformal coating materials in the market and highlights some of the key considerations.

SCH Technologies

Designing Circuit Boards for Selective Robotic Coating Application

Technical Library | 2013-10-13 10:36:21.0

Designing circuit boards for selective robotic spraying of conformal coating can be straightforward if you follow some design rules. Follow them and you can save money and time in your application process. However, if the rules are not followed, the resultant circuit board design can challenge even the most sophisticated conformal coating system and its operator to achieve the finish desired.

SCH Technologies

  1 2 Next

through-hole robotic systems searches for Companies, Equipment, Machines, Suppliers & Information

2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven
Selective Soldering Nozzles

Training online, at your facility, or at one of our worldwide training centers"
SMT Machines

World's Best Reflow Oven Customizable for Unique Applications
used smt parts china

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Assembly Automation Technology

Reflow Soldering Oven & Pressure Curing Oven Manufacturer in India