Technical Library | 2022-07-11 09:24:48.0
The change of squeegee pressure has a significant impact on printing. Too small pressure will make the solder paste unable to effectively reach the bottom of the stencil opening and not be well deposited on the pad. Too much pressure will cause tin The paste is printed too thin and can even damage the stencil.
Technical Library | 2023-09-23 22:29:02.0
Moisture trapped within components and PBs presents a serious problem during the fabrication and assembly process. Too much moisture can lead to board failures when it is turned to steam during the reflow process.
Technical Library | 2019-04-30 08:04:19.0
Every industry has every unwritten rules, like IC shipping tube moq is high in packaging tube industry rules! This regulation is not to be difficult for customers, but the cost of the problem, as long as the manufacturers feel that even a small amount of packaging tube can do and do too.
Technical Library | 2010-08-26 21:06:17.0
Driven by high-profile regulations compliance like the TREAD Act, warranty management has become a hot topic across industries worldwide. Recalls are costly and time-consuming events that should be avoided entirely. But without adequate process traceability and product genealogy, too many customers will get defective products and too many products will be recalled for repair or replacement even though they are not defective. Both scenarios have enormous implications for the quality-conscious manufacturer that gets rated on the number of recalls it performs - not to mention the enormous direct costs. The core issue is visibility into product quality.
Technical Library | 2005-05-16 12:09:02.0
Low cost techniques for building prototype and low volume SMT printed circuit boards.
Technical Library | 2021-07-28 18:35:13.0
The performance of electronic components is compromised by factors such as bubbles in the potting medium. Increasing numbers of applications – particularly in the automotive and electronics industries – therefore require completely bubble-free dispensing methods. This is where potting in a vacuum comes into focus. The widespread school of thought about this technology is that it is too complicated, too expensive and too slow. But a closer look shows that this view is incorrect. This is a mastered technology. As for costs, the calculation basis is key, since usually the potting and vacuum method is only considered after the required potting quality cannot be achieved reliably any other way. Under total cost of ownership assessments, higher system costs no longer play a key role, since component failure would result in much higher subsequent costs. And now there are proven solutions for high production volumes and/or shorter cycle times. This whitepaper explains when potting in a vacuum is ideal for your projects and what to be aware of.
Technical Library | 2015-07-21 13:50:37.0
Achieving an even coat at the right desired thickness is a major challenge when it comes to applying conformal coating to a Printed Circuit Board (PCB). Applying a coating too thin will ultimately render the electronic assembly vulnerable to potential environmental risks therefore defeating the purpose of the coating. Apply the coat too thick, and it could leave the electronic specific components non-functional therefore destroying the electronic assembly entirely. Coating thickness must meet quality specifications. Measurements for coating thickness may be taken while film is dry or wet. Once measurements are recorded, thickness is compared to quality specifications and fluid dispensing automation machinery is calibrated as necessary. There are a handful of methods for measuring conformal coating thickness that are commonly used in the Electronic Manufacturing Services (EMS) and Original Electronic Manufacturer (OEM) industries. A few commonly used methods for checking conformal coating thickness include:
Technical Library | 2019-06-06 00:19:02.0
More and more people and things are using electronic devices to communicate. Subsequently, many electronic products, in particular mobile base stations and core network nodes, need to handle enormous amounts of data per second. One important link in this communication chain is high speed pressfit connectors that are often used to connect mother boards and back planes in core network nodes. These new high speed pressfit connectors have several hundreds of thin, short and weak pins that are prone to damage. Small variations in via hole dimensions or hole plating thickness affect the connections; if the holes are too small, the pins may be bentor permanently deformed and if the holes are too large they will not form gas tight connections.The goal of this project was to understand how rework of these new high speed pressfit connectors affects connection strengths, hole wall deformations and plating cracks.
Technical Library | 2017-11-03 13:34:15.0
As with any production industry, businesses in the PCB industry need to maintain a healthy balance between the components they keep in stock and those they use for meet client orders. Ordering too many components comes with serious disadvantages, as does not ordering enough, and PCB manufacturers need to stay as close as possible to a happy medium between the two.
Technical Library | 2014-05-12 15:32:17.0
The issue of lead-free soldering has piqued a great deal of interest in the electronics assembly industry as of late. What was once an issue that seemed too far away to worry about has become a pressing reality. In order to avoid confusion, last minute panic, and a misunderstanding of how the issue of lead-free soldering will affect the industry and individuals users of solders, it is necessary for all suppliers and assemblers to become educated in this matter.
.gif)
winsouce.jpg)