Technical Library | 2018-09-21 10:12:53.0
Moisture accumulates during storage and industry practice recommends specific levels of baking to avoid delamination. This paper will discuss the use of capacitance measurements to follow the absorption and desorption behaviour of moisture. The PCB design used in this work, focused on the issue of baking out moisture trapped between copper planes. The PCB was designed with different densities of plated through holes and drilled holes in external copper planes, with capacitance sensors located on the inner layers. For trapped volumes between copper planes, the distance between holes proved to be critical in affecting the desorption rate. For fully saturated PCBs, the desorption time at elevated temperatures was observed to be in the order of hundreds of hours. Finite difference diffusion modelling was carried out for moisture desorption behaviour for plated through holes and drilled holes in copper planes. A meshed copper plane was also modelled evaluating its effectiveness for assisting moisture removal and decreasing bake times. Results also showed, that in certain circumstances, regions of the PCB under copper planes initially increase in moisture during baking.
Technical Library | 2013-08-13 09:49:53.0
One of the common issues I’ve noticed when visiting shops that use crimp force monitors (CFMs) is that the CFMs are usually turned off, regardless of the brand, because engineers and operators are not using them properly. Why, with all of their benefits, are CFMs not being used regularly by employees? One of the biggest problems is the lack of understanding of the variables affecting the CFM’s ability to detect variations. Crimp quality detection is similar to baking a cake. There are a lot of ingredients and if one ingredient is missing or of bad quality, you likely are not going to achieve your desired result. This article will go back through the basics of a crimp quality detection system and discuss what ingredients or variables you need to consider before switching off that CFM.
Technical Library | 2017-08-12 16:04:30.0
PCB Assembly is Collaborative Manufacturing
Technical Library | 2017-08-25 14:48:39.0
High Quality Solutions to Reduce Manufacturing Costs and Time
Technical Library | 2017-11-14 15:30:04.0
Can you put a product that hasn't been fully tested on the market? When it comes to Printed Circuit Board (PCB) assembly and manufacturing, most firms’ answer is neither a strict yes or no.
Technical Library | 2014-02-13 16:46:23.0
The high speed transmission applications in the electronic product become inevitable developing trend. The signal integrity becomes the most important issue in the electronics industry. The material suppliers, PCB manufacturers, OEM designers commonly face the serious issue "how to keep signal integrity operated in the high speed transmission" for the modern electronic application nowadays
Technical Library | 2014-08-19 15:39:13.0
Understanding warpage of package attach locations on PCBs under reflow temperature conditions is critical in surface mount technology. A new industry standard, IPC 9641, addresses this topic directly for the first time as an international standard.This paper begins by summarizing the sections of the IPC 9641 standard, including, measurement equipment selection, test setup and methodology, and accuracy verification. The paper goes further to discuss practical implementation of the IPC 9641 standards. Key advantages and disadvantages between available warpage measurement methods are highlighted. Choosing the correct measurement technique depends on requirements for warpage resolution, data density, measurement volume, and data correlation. From industry experience, best practice recommendations are made on warpage management of PCB land areas, covering how to setup, run, analyze, and report on local area PCB warpage.The release of IPC 9641 shows that flatness over temperature of the package land area on the PCB is critical to the SMT industry. Furthermore, compatibility of shapes between attaching surfaces in SMT, like a package and PCB, will be critical to product yield and quality in years to come.
Technical Library | 2018-08-03 14:37:59.0
In the electronics industry, the quality and reliability of any product is highly dependent upon the capabilities of the manufacturing suppliers. Manufacturing defects are one of the top reasons why companies fail to meet warranty expectations. These problems can result in severe financial pain and eventual loss of market share. What a surprising number of engineers and managers fail to realize is that focusing on processes addresses only part of the issue. Supplier selection also plays a critical role in the success or failure of the final product.
Technical Library | 2014-04-03 18:01:13.0
A system level modeling methodology is presented and validated on a simple case. It allows precise simulations of electrostatic discharge (ESD) stress propagation on a printed circuit board (PCB). The proposed model includes the integrated circuit (IC) ESD protection network, IC package, PCB lines, passives components, and externals elements. The impact of an external component on the ESD propagation paths into an IC is demonstrated. Resulting current and voltage waveforms are analyzed to highlight the interactions between all the elements of an operating PCB. A precise measurement technique was designed and used to compare with the simulation results. The model proposed in this paper is able to predict, with good accuracy, the propagation of currents and voltages into the whole system during ESD stress. It might be used to understand why failures occur and how to fix them with the most suitable solution.
Technical Library | 2023-11-14 19:42:24.0
Selective soldering is not a new process. It is already exists and used 30 years ago for through-hole component by different industries for automotive and medical products. Now most manufacturing industries are moving forward on SMD's miniaturization to reduce PCB complexity and balance component density on the board to ensure a good assembling process. By this concept, why selective soldering still utilized and used? Does it because of component reliability, uniqueness or complexity having this in mind next question will be which platform will best fit for the product
