Technical Library | 2007-04-04 11:43:41.0
The present work offers a discussion and a first case study to identify and illustrate voiding mechanisms for a particular TIM between a heat spreader and the back of a flip chip. Pronounced differences were observed between stencil printing and dispensing in terms of initial void formation, apparently related to the specific properties of the material. Measurements of the effects of heat ramp rate and peak temperature showed the subsequent evolution and final void size distribution to be determined by the initial part of the cure profile up to the material gelling temperature.
Technical Library | 2007-07-12 14:29:37.0
Over the last ten years, there have been a large number of publications describing work into lead free electronics soldering. They have come from all regions of the world and from academic organisations, individual companies and consortia. Although a number of these studies have culminated in "production trials", these have invariably been on a limited scale and they were essentially a demonstration, rather than the first step to implementation.
Technical Library | 2007-12-27 11:41:37.0
The latest screen printing platforms unlock more of the potential from dual-lane processing. Simultaneous demands to enhance flexibility while increasing utilisation and overall throughput apply to manufacturers operating at virtually any point in the mix-volume continuum: capacity must work hard to deliver the required return. As these lean manufacturing principles hold sway from the US and Europe to the Far East, no modern assembler has a second to spare.
Technical Library | 2008-03-03 19:43:53.0
Solder pastes are key materials in surface mount technology (SMT) for assembly of printed circuit boards (PCBs). Introduction of lead-free has placed new demands on materials and processes in SMT, requiring materials and process engineers to adopt to lead free whilst ensuring process yields stay at the highest possible levels. Key is the solder paste, a material of great complexity involving engineering sciences, metallurgy, chemistry and physics. This article helps those working with solder pastes improve their understanding of this key material.
Technical Library | 2010-04-15 20:42:44.0
The high level of current interest in embedded passives in printed circuit boards is driven by the tremendous pressure to pack more circuitry into smaller spaces. However, adoption has been limited due to design, prototyping and infrastructure issues, as well as the stability and tolerances necessary for widespread replacement of discretes. The focus of this work has been to develop a polymer thick film resistor technology to incorporate reliable organic resistors inside printed wiring boards using standard PWB processing.
Technical Library | 2016-06-21 09:15:31.0
The trends in mobile electronics today are smaller, thinner and lighter. Yet, mobile devices are more powerful than ever. Applications, like wireless internet connections, RFID and Bluetooth, that have become essential in today’s devices, require more complex transmission mechanisms. As a result, manufacturers find themselves faced with the challenge of working with ultra-miniature RF cable assemblies.
Technical Library | 2016-11-30 21:30:50.0
Mid-chip solder balling is a defect typically associated with solder paste exhibiting poor hot slump and/or insufficient wetting during the reflow soldering process, resulting in paste flowing under the component or onto the solder resist. Once molten, this solder is compressed and forced to the side of the component, causing mid-chip solder balling.This paper documents the experimental work performed to further understand the impact on mid-chip solder balling from both the manufacturing process and the flux chemistry.
Technical Library | 2017-11-03 13:39:06.0
If someone were to ask what the most important part of their favorite electronic device is, they are likely to point to the printed circuit board (PCB) responsible for making the device work before moving on to other components. From large motherboards to tiny chips, most of the technology that retail consumers take for granted comes down to a properly installed and calibrated PCB.
Technical Library | 2021-03-18 20:07:08.0
X-ray tomography is a promising technique that can provide micron level, internal structure, and three dimensional (3D) information of an integrated circuit (IC) component without the need for serial sectioning or decapsulation. This is especially useful for counterfeit IC detection as demonstrated by recent work. Although the components remain physically intact during tomography, the effect of radiation on the electrical functionality is not yet fully investigated. In this paper we analyze the impact of X-ray tomography on the reliability of ICs with different fabrication technologies.
Technical Library | 2021-12-17 01:30:28.0
Diffusion silicon pressure transmitter is applied in a wide variety of industries, such as petroleum, chemical industry, steel, power, light industry and environmental protection industry. It can complete the work of measurement and control of the gauge pressure, negative pressure or absolute pressure of various fluid pressure. Most importantly, this type of transmitter can be used in corrosive medium and harsh or dangerous environment. In the process of using the transmitter, there may be some faults or problems.
