Industry Directory | Consultant / Service Provider / Manufacturer
Action Controls, Inc. is a (Seattle area) based contract electronic manufacturer (CEM) that has been delivering high quality electronic manufacturing services (EMS), since 1991 to customers across both domestic and global markets.
Industry Directory | Consultant / Service Provider
XJTAG provides a full range of JTAG products to help you debug board designs with BGAs, test hardware that includes FPGAs, CPLDs, DSPs or microprocessors.
Cut panels without scoreline and with overhanging components. The S300 diamond blade depaneling saw is ideal for use in singulating assembled PCBs. Singulate panels up to 12" wide. Microprocessor controlled STI safety interlock Long Lasting Di
Two non-latching user inputs (three screw terminals; Record, Common & Stop) External power supply (6 to 9.5 VDC) Unit switch on with short circuit applied to REC input and start recording Unit stop recording and switch to soft off with short circuit
Electronics Forum | Fri Nov 07 06:06:27 EST 2003 | loz
Tape and reeling services as follows:- Specific Components Ltd. Tel. 01257 279944 Others available are Action Circuits, in Luton. Intosert in Northampton. Sorry no contact details for above. Loz
Electronics Forum | Tue Aug 17 15:58:14 EDT 2010 | rob_thomas
IPC-7711/7721 states under Scope section: "This document does not limit the maximum number of rework, modification or repair actions to a Printed Circuit Assembly". This is from Rev B of this standard. There are many factors that play a role in the d
Used SMT Equipment | In-Circuit Testers
Fluke 810 Vibration Tester The Fluke 810 Vibration Tester is the most advanced troubleshooting tool for mechanical maintenance teams who need an answer now. The unique diagnostic technology helps you quickly identify and prioritize mechanical p
Used SMT Equipment | In-Circuit Testers
Fluke 810 Vibration Tester The Fluke 810 Vibration Tester is the most advanced troubleshooting tool for mechanical maintenance teams who need an answer now. The unique diagnostic technology helps you quickly identify and prioritize mechanical p
Industry News | 2003-03-14 08:54:29.0
The action is part of its continuing efforts to serve its many loyal customers, the company said.
Industry News | 2003-02-14 08:28:51.0
Will Increase Its Equity Investment in Its Wholly-owned Unit in China, Grand Circuit Industry (Suzhou) Co.
Technical Library | 2024-01-08 21:31:01.0
The aim of this collection and interpretation is to develop an understanding of moisture in materials, especially in printed circuit boards, to know the effects on further processing and to be able to derive targeted corrective actions when moisture-related problems occur. In principle, the considerations are valid for all types of PCBs. Although these basic principles are of particular importance when working with flexible and rigid-flexible printed circuit boards; observing them can mean the difference between success or failure.
Technical Library | 2020-08-27 01:22:45.0
Initially adopted internal specifications for acceptance of printed circuit boards (PCBs) used for wire bonding was that there were no nodules or scratches allowed on the wirebond pads when inspected under 20X magnification. The nodules and scratches were not defined by measurable dimensions and were considered to be unacceptable if there was any sign of a visual blemish on wire-bondable features. Analysis of the yield at a PCB manufacturer monitored monthly for over two years indicated that the target yield could not be achieved, and the main reasons for yield loss were due to nodules and scratches on the wirebonding pads. The PCB manufacturer attempted to eliminate nodules and scratches. First, a light-scrubbing step was added after electroless copper plating to remove any co-deposited fine particles that acted as a seed for nodules at the time of copper plating. Then, the electrolytic copper plating tank was emptied, fully cleaned, and filtered to eliminate the possibility of co-deposited particles in the electroplating process. Both actions greatly reduced the density of the nodules but did not fully eliminate them. Even though there was only one nodule on any wire-bonding pad, the board was still considered a reject. To reduce scratches on wirebonding pads, the PCB manufacturer utilized foam trays after routing the boards so that they did not make direct contact with other boards. This action significantly reduced the scratches on wire-bonding pads, even though some isolated scratches still appeared from time to time, which caused the boards to be rejected. Even with these significant improvements, the target yield remained unachievable. Another approach was then taken to consider if wire bonding could be successfully performed over nodules and scratches and if there was a dimensional threshold where wire bonding could be successful. A gold ball bonding process called either stand-off-stitch bonding (SSB) or ball-stitch-on-ball bonding (BSOB) was used to determine the effects of nodules and scratches on wire bonds. The dimension of nodules, including height, and the size of scratches, including width, were measured before wire bonding. Wire bonding was then performed directly on various sizes of nodules and scratches on the bonding pad, and the evaluation of wire bonds was conducted using wire pull tests before and after reliability testing. Based on the results of the wire-bonding evaluation, the internal specification for nodules and scratches for wirebondable PCBs was modified to allow nodules and scratches with a certain height and a width limitation compared to initially adopted internal specifications of no nodules and no scratches. Such an approach resulted in improved yield at the PCB manufacturer.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Successful manufacturing requires that the materials are in the right place Just on Time. Our board handling products are known for high quality, even our first PCB handling products from early 90’s are still used in many factories around the world.
Events Calendar | Wed Dec 01 00:00:00 EST 2021 - Wed Dec 01 00:00:00 EST 2021 | ,
Wine Down Wednesday: Driving Innovation through Intrapreneurship
Career Center | Florham Park, New Jersey USA | Engineering
Field Service Engineer Job Description The basic function of this position: Installation, training, repair, and implementation of retrofits on the complete line of Heller reflow ovens. Candidate must be a US citizen. DUTIES AND RESPONSIBILITIES: S
Career Center | Meridian, Idaho USA | Quality Control
Actively participate in continuous improvement activities at the product, process, and Quality System level. Identify unique customer quality requirements then develop, maintain, and improve the tools to support these requirements for printed cir
Career Center | Fredericksburg, Virginia USA | Engineering,Maintenance,Management,Production,Quality Control
• Certified CP643 Loader Calibration – FUJI American Chicago, IL 2001. • Certified - Cookson Performance Solutions BTU - PARAGON - P150 Oven – Maintenance & Electrical Troubleshooting Charlotte, NC 2001. • Certified UNIVERSAL (GSM) Platform: Operat
Career Center | Chennai, India | Sales/Marketing
Experience in sales of inter-connect, passive, active, and electro-mechanical components Product Engineering Role as handling BOM, ECO, ECN in the New product introduction of Philips LCD TV and Kulicke and Soffa wire bonding m/c Process and Quali
| https://www.eptac.com/wp-content/uploads/2013/06/eptac_06_19_13.pdf
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/asymtek/products/fluid-dispensing-systems/spectrum-ii-s2-900-precision-fluid-dispensing-system
. New features and upgrade options for the Spectrum II systems continue to expand upon the wide range of applications. Whether it is dispensing underfill in PCBA applications, precise coating on mobile electronics and flexible circuits, or