Industry Directory | Manufacturer
EL.CO. manufactures automation accessories like solid state relays and power units, but also temperature controllers and probes
Industry Directory | Consultant / Service Provider
Subcontract electronic, mechanical, optical, embedded software design & development
A500, A600, A800 - 5, 6 or 8 top/bottom cooling zones. Heating System: Up to eight groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air co
S8, S10, S12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
Electronics Forum | Tue Jan 08 17:29:20 EST 2002 | davef
Your research is on track. NC flux needs to reach activation temperature. Also, do not depend on the corrosion characteristics associated with the flux classification (ie, L1, L0, M1, M0, etc.), until the flux is activated by exposure to soldering
Electronics Forum | Wed Mar 16 08:06:52 EST 2005 | zsolt
Grant is right, also for us was the easiest solution to us custom pallets. But you should also try to tweak preheat zones settings. The flux manufacturer should give you some basic temperatures where the flux gets activated. Also it is worth to make
Used SMT Equipment | Soldering - Wave
Solder type lead free solder Max PCB 50—250mm Components height Above ?130mm under ?8mm Pot Capacity 130KG ( Titanium / SUS316 ) Preheating length
Used SMT Equipment | Soldering - Reflow
Desk Reflow Oven Features: Cost-effective Desk Reflow Oven utilizes forced air convection heating technology and PC software interface to make an accurate temperature profile quickly and easily. T200 is a fine temperature profile model wit
Industry News | 2003-03-06 08:10:20.0
Astec Power has expanded its popular APC-Centauri surface-mount product line to include a series of 40W point-of-load DC/DC convertors.
Industry News | 2018-10-18 09:37:27.0
How To Set Profile In SMT Reflow Oven
Parts & Supplies | Soldering - Wave
Overseas Agent and Distributor Wanted ! Features : Spray Fiuxer: 1) Oriental motor drives the flux spraying system. Spraying speed is adjusted according to PCB board width and moving speed to ensure even spraying all time. 2) Durable “Meiji
Parts & Supplies | Assembly Accessories
JUKI NGA JIP PLATE A ASM E21499980A0 We are Supply SMT Pick and Place Equipment spare parts(Smt nozzle, Smt Cylinder, Smt Valve, Smt Sensor, Smt Feeder, Smt CPU Board, Smt Laser, Smt driver, Smt ejector……) for Yamaha, JUKI, FUJI ,Panasonic, Samsun
Technical Library | 2016-10-24 14:59:03.0
Temperature measurement is one of the most important physical parameters when determining quality, accuracy and reliability of processes not only in industrial use, but also in almost all human activities. Temperature sensors are produced with different technologies to fit specific application requirements. IST AG has concentrated one part of the development and manufacturing on high-end thin-film temperature sensors. This know-how is partially derived from the semiconductor industry and allows us to manufacture sensors with high accuracy, excellent long-term stability, high reliability and repeatability within a wide temperature range from -200 °C up to 1000 °C. Because of very small dimensions and low thermal mass, the thin-film temperature sensors exhibit a very short response time.
Technical Library | 2020-12-10 15:49:40.0
Electronic assemblies should have longer and longer service life. Today there are partially demanded 20 years of functional capability for electronics for automotive application. On the other hand, smaller components, such as resistors of size 0201, are able to endure an increasing number of thermal cycles until fail of solder joints, so these are tested sometimes up to 4000 cycles. But testing until the end of life is essential for the determination of failure rates and the prognosis of reliability. Such tests require a lot of time, but this is often not available in developing of new modules. A further acceleration by higher cycle temperatures is usually not possible, because the materials are already operated at the upper limit of the load. However, the duration can be shortened by the use of liquids for passive tests, which allow faster temperature changes and shorter dwell times because of better heat transfer compared to air. The question is whether such tests lead to comparable results and what failure mechanisms are becoming effective. The same goes for active temperature cycles, in which the components itself are heated from inside and the substrate remains comparatively cold. This paper describes the various accelerated temperature cycling tests, compares and evaluates the related degradation of solder joints.
A500, A600, A800 - 5, 6 or 8 top/bottom cooling zones. Heating System: Up to eight groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air co
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Wed Jun 22 00:00:00 EDT 2022 - Wed Jun 22 00:00:00 EDT 2022 | ,
Empire Chapter Webinar: LIVE Action Reflow Focused Process
Career Center | New Castle, Pennsylvania USA | Production
Surface Mount Tech - Printed Circuit Board (PCB) Summary: **All applicants must be familiar with: Quad 4C equipment*** Will be responsible for Surface Mount Parts and Screen Printing Other responsibilities may include: Moves controls to activate
Career Center | Brooklyn, New York USA | Engineering,Management
Mini-Circuits designs, manufactures and distributes integrated circuits, modules, and sub-systems for high performance radio frequency (RF) and microwave applications. With design, sales and manufacturing locations in over 30 countries, Mini-Ci
Career Center | sultanpur, U.P. India | Engineering,Sales/Marketing
Experience: • Working with DA Groups -TARA Machines & Tech Services Pvt. Ltd. as a Asst. Manager -Sales. (a) From 4th Feb 2012 to present. • Worked with DVS India Pvt. Ltd. as a Sales & Service Engineer. (a) From 4th June 2010 to 31st
Career Center | Cochin, Kerala India | Engineering,Management,Production,Technical Support
9 Years Experience in SMT Manufacturing Process, Quality Control Process, Testing and Engineering of Windmill power projects. The experience include: - � Skill in selection and installation of new manufacturing lines. � Conduct and analyze process t
1st Place Machinery Inc. | http://www.firstplacemachinery.com/first_place_smt_pcb_wave_solder_vitronics.html
). Activation aireknife via tracking system Stone Material: VYON FF Stone Porosity: 35 micron Compressed Air Control Unit: Standard Air Compressor
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/applications/plasma-treating?con=t&page=15
. Nordson MARCH plasma treatment systems can perform numerous surface modification processes including surface activation, contamination removal, cross linking, etch by chemical reaction, and physical bombardment
winsouce.jpg)
